Thermostatic Valve - Assemble
组装步骤
- 安装螺栓 (3) 以将座盘 (2) 安装到上部壳体 (1) 上。 用 20 ± 2 N·m (15 ± 2 lb ft) 的扭矩拧紧螺栓 (3) 。
Show/hide table
图 1 | g00997739 |
- 将套筒 (4) 和 O 形密封圈 (5) 安装到上部壳体 (1) 上。
- 安装 O 形密封圈 (6) 和上部壳体 (1) 。
- 将调节器组件 (8) 安装在上部壳体 (1) 上。
- 安装螺栓 (7) ,以便将下部壳体 (9) 安装到上部壳体 (1) 上。
End By: 安装节温器阀。 请参阅 拆解与组装节温器, "阀 - 安装"。
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Thermostatic Valve - Disassemble
3054C Industrial Engine Idler Gear - Remove and Install - Bosch EPVE Fuel Injection Pump
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0277 - FMI 08 Timing Calibration signal abnormal
Recommendations for Caterpillar Gas Engine Cooling Systems{1350} Recommendations for Caterpillar Gas Engine Cooling Systems{1350}
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0091 - FMI 13 Throttle Position calibration required
3406C Generator Sets Model View Illustrations
Installation of Double Lip Wiper Seal{7562} Installation of Double Lip Wiper Seal{7562}
3406C Generator Sets Safety Messages
2003/10/06 Installation of the Correct Dust Seal in the Swing Gear and Bearing {7063}
G3304 and G3306 Engines Magneto - Assemble
C1.5 and C2.2 Marine Generator Set Engines Engine Oil Line - Remove and Install
G3520C and G3520E Generator Set Engines Cylinder Head - Install
Caterpillar has released a new Cylinder Head, a new Cylinder Block, a new Cylinder Head Gasket, and a new Bracket for the Camshaft Follower on the C-10 and C-12 Truck Engines{1101, 1124, 1201, 1209} Caterpillar has released a new Cylinder Head, a new Cylinder Block, a new Cylinder Head Gasket, and a new Bracket for the Camshaft Follower on the C-10 and C-12 Truck Engines{1101, 1124, 1201, 1209}
G3520C and G3520E Generator Set Engines Crankcase Breather - Remove and Install
G3520C and G3520E Generator Set Engines Thermostatic Valve - Remove
G3520C and G3520E Generator Set Engines Thermostatic Valve - Install
G3304 and G3306 Engines Magneto Drive - Remove and Install
G3520C and G3520E Generator Set Engines Exhaust Manifold - Remove
G3520C and G3520E Generator Set Engines Exhaust Manifold - Install
2003/06/01 SOLAS Requirement for Screening Fuel and Oil Line Connections on Marine Engines {1274, 1307}
3500B Marine Engines MID 036 - CID 0267 - FMI 02 Incorrect Engine Shutdown Switch inputs
3500B Marine Engines MID 036 - CID 0267 - FMI 03 Remote Shutdown Input open/short to +batt
3500B Marine Engines MID 036 - CID 0267 - FMI 04 Remote Shutdown Input short to ground
3116 and 3126 Truck Engines Cylinder Head - Remove