Exhaust Manifold - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1U-9200     | 操纵杆滚轮起重机     | 1     |
189-0412 | 钩环组件     | 1     | |
B     | 5P-3931     | 防粘结剂     | -     |
C     | - (1)     | 镍基防咬合剂     | -     |
Show/hide table
( 1 ) | 有关制造商零件号,请参考技术信息公告, TIBU 5269。 |
- 将工具 (A) 和适当的起吊设备连接到排气歧管 (6) 上。 排气歧管 (6) 的重量约为 136 kg (300 lb)。
Show/hide table
图 1 | g00998149 |
- 定位排气歧管 (6) 和密封件。
Show/hide table
图 2 | g00998147 |
- 将工具 (B) 涂抹到螺栓 (5) 和垫圈上。
- 安装螺栓 (5) 。 用 55 ± 5 N·m (41 ± 4 lb ft) 的扭矩拧紧螺栓 (5) 。
- 将工具 (B) 涂抹到卡箍 (8) 上。
- 定位卡箍 (8) 。
- 将工具 (B) 涂抹到螺栓 (7) 上。
- 安装螺栓 (7) 。 将螺栓 (7) 上紧到 25 ± 6 N·m (18 ± 4 lb ft) 的扭矩。
- 如有必要,请在排气歧管 (6) 上安装热电偶。 安装之前先在热电偶上涂抹工具 (C) 。 如果热电偶为直式,拧紧螺母至扭矩为 25 ± 5 N·m (18 ± 4 lb ft)。 若热电偶有 90 度弯曲,拧紧螺母至扭矩为 12 ± 3 N·m (105 ± 27 lb in)。
- 连接线束组件 (4) 。
- 卸下护罩组件 (3) 。
Show/hide table
图 3 | g00998146 |
- 安装护罩组件 (2) 和板 (1) 。
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Exhaust Manifold - Remove
G3304 and G3306 Engines Magneto Drive - Remove and Install
G3520C and G3520E Generator Set Engines Thermostatic Valve - Install
G3520C and G3520E Generator Set Engines Thermostatic Valve - Remove
G3520C and G3520E Generator Set Engines Crankcase Breather - Remove and Install
Caterpillar has released a new Cylinder Head, a new Cylinder Block, a new Cylinder Head Gasket, and a new Bracket for the Camshaft Follower on the C-10 and C-12 Truck Engines{1101, 1124, 1201, 1209} Caterpillar has released a new Cylinder Head, a new Cylinder Block, a new Cylinder Head Gasket, and a new Bracket for the Camshaft Follower on the C-10 and C-12 Truck Engines{1101, 1124, 1201, 1209}
G3520C and G3520E Generator Set Engines Thermostatic Valve - Assemble
G3520C and G3520E Generator Set Engines Thermostatic Valve - Disassemble
3054C Industrial Engine Idler Gear - Remove and Install - Bosch EPVE Fuel Injection Pump
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0277 - FMI 08 Timing Calibration signal abnormal
Recommendations for Caterpillar Gas Engine Cooling Systems{1350} Recommendations for Caterpillar Gas Engine Cooling Systems{1350}
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0091 - FMI 13 Throttle Position calibration required
2003/06/01 SOLAS Requirement for Screening Fuel and Oil Line Connections on Marine Engines {1274, 1307}
3500B Marine Engines MID 036 - CID 0267 - FMI 02 Incorrect Engine Shutdown Switch inputs
3500B Marine Engines MID 036 - CID 0267 - FMI 03 Remote Shutdown Input open/short to +batt
3500B Marine Engines MID 036 - CID 0267 - FMI 04 Remote Shutdown Input short to ground
3116 and 3126 Truck Engines Cylinder Head - Remove
G3520C and G3520E Generator Set Engines Spark Plug - Remove and Install
G3520C and G3520E Generator Set Engines Flywheel Housing - Remove
G3520C and G3520E Generator Set Engines Flywheel Housing - Install
3116 and 3126 Truck Engines Fuel Transfer Pump - Remove
G3500B Engines Air/Fuel Ratio Control - Oxygen Feedback
3116 and 3126 Truck Engines Fuel Transfer Pump - Install
2003/05/01 Compression Brakes Should be Inspected Carefully During Repairs to the Cylinder Head and Valve Mechanism {1119}