Magneto Drive - Remove and Install
Show/hide table
Required Tools | |||
Tooling | Part Number | Description | Qty |
A | 8S-2264 | Puller | 1 |
9S-9155 | Spacer | 1 | |
0S-1605 | Bolt | 2 | |
4B-4278 | Washer | 3 |
Start By:
- Remove the service meter. Refer to Disassembly and Assembly, "Service Meter - Remove and Install" for the engine that is being serviced.
- Remove the magneto. Refer to Disassembly and Assembly, "Magneto - Remove and Install" for the engine that is being serviced.
- Remove nuts (1), the washers, cover (2), and the gasket from the front housing.
Show/hide table
Illustration 2 g00998068 - Remove bolt (3) and the washer.
Show/hide table
Illustration 3 g00998070 - Place Tooling (A) in position on drive gear (4).
- Use Tooling (A) in order to loosen drive gear (4) from the sleeve of the magneto drive. Remove Tooling (A).
Show/hide table
Illustration 4 g00998071 - Disconnect oil supply tube assembly (7) from magneto drive (6).
- Remove nuts (5) and the washers that hold magneto drive (6) in place. Remove magneto drive (6).
Show/hide table
Illustration 1 | g00998067 |
- Place magneto drive (6) in position on the front housing.
Show/hide table
Illustration 6 g00998077 - Install nuts (5) and the washers.
- Connect oil supply tube assembly (7) to the magneto drive.
Show/hide table
Illustration 7 g00998092 - Install bolt (3) and the washer. Tighten bolt (3) to a torque of
149 ± 7 N·m (110 ± 5 lb ft) .Show/hide tableIllustration 8 g00998067 - Install the gasket and cover (2) on the front housing. Tighten the nuts (1) that hold cover (2) in place to a torque of
25 ± 7 N·m (18 ± 5 lb ft) .
Show/hide table
Illustration 5 | g00998076 |
End By:
- Install the magneto. Refer to Disassembly and Assembly, "Magneto - Remove and Install" for the engine that is being serviced.
- Install the service meter. Refer to Disassembly and Assembly, "Service Meter - Remove and Install" for the engine that is being serviced.
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Thermostatic Valve - Install
G3520C and G3520E Generator Set Engines Thermostatic Valve - Remove
G3520C and G3520E Generator Set Engines Crankcase Breather - Remove and Install
Caterpillar has released a new Cylinder Head, a new Cylinder Block, a new Cylinder Head Gasket, and a new Bracket for the Camshaft Follower on the C-10 and C-12 Truck Engines{1101, 1124, 1201, 1209} Caterpillar has released a new Cylinder Head, a new Cylinder Block, a new Cylinder Head Gasket, and a new Bracket for the Camshaft Follower on the C-10 and C-12 Truck Engines{1101, 1124, 1201, 1209}
G3520C and G3520E Generator Set Engines Thermostatic Valve - Assemble
G3520C and G3520E Generator Set Engines Thermostatic Valve - Disassemble
3054C Industrial Engine Idler Gear - Remove and Install - Bosch EPVE Fuel Injection Pump
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0277 - FMI 08 Timing Calibration signal abnormal
Recommendations for Caterpillar Gas Engine Cooling Systems{1350} Recommendations for Caterpillar Gas Engine Cooling Systems{1350}
3500B and 3500C Marine Propulsion Engines MID 036 - CID 0091 - FMI 13 Throttle Position calibration required
3406C Generator Sets Model View Illustrations
Installation of Double Lip Wiper Seal{7562} Installation of Double Lip Wiper Seal{7562}
G3520C and G3520E Generator Set Engines Exhaust Manifold - Remove
G3520C and G3520E Generator Set Engines Exhaust Manifold - Install
2003/06/01 SOLAS Requirement for Screening Fuel and Oil Line Connections on Marine Engines {1274, 1307}
3500B Marine Engines MID 036 - CID 0267 - FMI 02 Incorrect Engine Shutdown Switch inputs
3500B Marine Engines MID 036 - CID 0267 - FMI 03 Remote Shutdown Input open/short to +batt
3500B Marine Engines MID 036 - CID 0267 - FMI 04 Remote Shutdown Input short to ground
3116 and 3126 Truck Engines Cylinder Head - Remove
G3520C and G3520E Generator Set Engines Spark Plug - Remove and Install
G3520C and G3520E Generator Set Engines Flywheel Housing - Remove
G3520C and G3520E Generator Set Engines Flywheel Housing - Install
3116 and 3126 Truck Engines Fuel Transfer Pump - Remove
G3500B Engines Air/Fuel Ratio Control - Oxygen Feedback