Flywheel Housing - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 147-6456     | 楔块拆卸工具     | 1     |
B     | 138-7573     | 连杆支架     | 4     |
C     | 138-7574     | 连杆支架     | 1     |
D     | 9U-6600     | 手动液压泵     | 1     |
8B-7548 | 推拉器工具总成     | 1     | |
8B-7559 | 适配器     | 2     | |
1P-0820 | 液压拉拔器     | 1     | |
5H-1504 | 硬垫圈     | 3     | |
E     | 138-7575     | 连杆支架     | 2     |
F     | 6V-2078     | 双头螺柱     | 2     |
G     | 169-5464     | 快速硫化底漆     | -     |
开始:
- 拆下发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸"。
- 拆下摇臂轴组件和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。
- 使用正时销正确正时发动机。 请参考测试和调整, "凸轮轴正时"。 请参考测试和调整, "确定 1 号活塞上止点位置"。
- 拆下盖 (1) 。
Show/hide table
图 1 | g01229405 |
- 使用工具 (A) 断开线束组件 (2) 。
Show/hide table
图 2 | g00998300 |
- 拔出穿过支架 (3) 的线束组件 (2) 。
- 从支架 (3) 上断开线束组件 (4) 。
- 将工具 (B) 和适当的起吊设备连接到支架 (3) 。 支架 (3) 的重量约为 36 kg (80 lb)。
- 拆下螺栓 (5) 和支架 (3) 。
- 拆下螺栓 (6) 和螺栓 (8) 。
Show/hide table
图 3 | g00998302 |
- 拆下弯头 (7) 和密封垫。
- 拆下螺栓 (10) 。
- 断开接头 (9) 和 O 形密封圈。
- 拆下螺栓 (11) 。
Show/hide table
图 4 | g00998303 |
- 断开适配器 (12) 和密封垫。
- 断开线束组件 (13) 。
- 拆下螺栓 (15) 。
- 断开接头 (14) 和 O 形密封圈。
- 将工具 (B) 和适当的起吊设备连接到调节器壳体组件 (16) 上。 调节器壳体组件 (16) 的重量约为 100 kg (220 lb)。
Show/hide table
图 5 | g00998304 |
Show/hide table
图 6 | g00998305 |
- 拆下螺栓 (17) 。
- 拆下调节器壳体组件 (16) 。
- 拆下螺栓 (18) 。
Show/hide table
图 7 | g00998306 |
Show/hide table
图 8 | g00998307 |
- 卸下支架组件 (19) 。
- 从发动机监控控制器 (21) 断开线束组件 (20) 。
Show/hide table
图 9 | g00998308 |
- 拆下螺栓 (22) 。
- 拆卸发动机监控控制器 (21) 和支架 (23) 。
- 拆下螺栓 (24) 。
Show/hide table
图 10 | g00998309 |
- 将支架 (25) 放在一边。
- 拆下支架 (26) 。
Show/hide table
图 11 | g00998311 |
- 拆下正时指针 (26A) 。
Show/hide table
图 12 | g01054295 |
- 在飞轮 (28) 上固定工具 (C) 和适当的起吊设备。 飞轮 (28) 的重量约为 172 kg (380 lb)。
Show/hide table
图 13 | g01002798 |
- 拆下两个螺栓 (27) 。 安装工具 (F) 。
- 拆下剩余的螺栓 (27) 。
- 拆下飞轮 (28) 。
- 拆下盖组件 (29) 。
Show/hide table
图 14 | g01002799 |
- 拆卸曲轴后密封件和耐磨衬套 (30) 。 参考拆解与组装, "曲轴后密封和耐磨衬套 - 拆卸"。
- 拆下转速传感器 (31) 。
Show/hide table
图 15 | g01002800 |
- 拆下螺栓 (32) 和正时环 (33) 。
Show/hide table
图 16 | g01002801 |
- 将螺栓 (34) 和板 (35) 从凸轮轴驱动齿轮 (36) 上拆下。
Show/hide table
图 17 | g01002802 |
- 将工具 (D) 的三个垫圈置于板 (35) 后面,并将螺栓和板 (35) 安装在凸轮轴驱动齿轮 (36) 上。
Show/hide table
图 18 | g01002803 |
- 在凸轮轴驱动齿轮 (36) 上安装工具 (D) 。 在拉拔器上施加 51675 kPa (7500 psi) 的作用力。 用锤子敲击工具 (D) 上的拉拔器螺钉头。 这将使凸轮轴驱动齿轮 (36) 自由脱离凸轮轴。
Show/hide table
注意 |
---|
对液压拉拔器施加的压力不要超过51675 kPa (7500 psi)。 接头的额定承重值为6 1/2吨,液压拉拔器在68900 kPa (10000 psi)压力下的额定值为17吨。 如果压力过大,可能损坏齿轮。 |
- 对其余齿轮重复执行步骤 38 至步骤 39。
- 将工具 (E) 和适当的起吊设备连接到飞轮壳体 (37) 上。 飞轮壳体 (37) 的重量约为 245 kg (540 lb)。
Show/hide table
图 19 | g01002804 |
- 拆卸螺栓 (38) 、螺栓 (39) 、螺栓 (41) 、螺栓 (42) 、螺栓 (43) 和螺栓 (44) 。
Show/hide table
图 20 | g01002926 |
- 拆下飞轮壳体 (37) 。
- 将垫片 (40) 从飞轮壳体 (37) 上拆下。
- 拆下飞轮壳体 (37) 后,用工具 (G) 清洁缸体配合面和飞轮壳体配合面。 如有必要,用密封垫刮刀和溶剂清除任何残留的密封垫材料。 安装前,两个配合面必须清洁、干燥且没有机油。
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Spark Plug - Remove and Install
3116 and 3126 Truck Engines Cylinder Head - Remove
3500B Marine Engines MID 036 - CID 0267 - FMI 04 Remote Shutdown Input short to ground
3500B Marine Engines MID 036 - CID 0267 - FMI 03 Remote Shutdown Input open/short to +batt
3500B Marine Engines MID 036 - CID 0267 - FMI 02 Incorrect Engine Shutdown Switch inputs
2003/06/01 SOLAS Requirement for Screening Fuel and Oil Line Connections on Marine Engines {1274, 1307}
G3520C and G3520E Generator Set Engines Exhaust Manifold - Install
G3520C and G3520E Generator Set Engines Exhaust Manifold - Remove
G3304 and G3306 Engines Magneto Drive - Remove and Install
G3520C and G3520E Generator Set Engines Thermostatic Valve - Install
G3520C and G3520E Generator Set Engines Thermostatic Valve - Remove
G3520C and G3520E Generator Set Engines Crankcase Breather - Remove and Install
G3520C and G3520E Generator Set Engines Flywheel Housing - Install
3116 and 3126 Truck Engines Fuel Transfer Pump - Remove
G3500B Engines Air/Fuel Ratio Control - Oxygen Feedback
3116 and 3126 Truck Engines Fuel Transfer Pump - Install
2003/05/01 Compression Brakes Should be Inspected Carefully During Repairs to the Cylinder Head and Valve Mechanism {1119}
3500B Engines Accessory Drive (Lower Left Hand, Reverse Rotation)
3456 Generator Sets Model View Illustrations
2003/05/01 Check OEM Web Sites for Service Letters and Information that may be Related to Product Campaigns {0374}
Cat® Digital Voltage Regulator General Information
BA-921 Bendix Air Compressor Specification
C27 and C32 Generator Sets Jacket Water Heater - Check - Standby Generator Sets (If Equipped)
C15 and C18 Petroleum Generator Sets Battery Charger - Check