Fuel Injection Pump - Install - Bosch EVPE
Show/hide table
Required Tools | |||
Tool | Part Number | Part Name | Qty |
A | 230-6284 | Timing Pin (Camshaft) | 1 |
B | 230-6283 | Timing Pin (Crankshaft) | 1 |
C | 9U-6198 | Crankshaft Turning Tool | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (C) to ensure that the No. 1 cylinder is at the top center compression stroke. Refer to Testing and Adjusting, "Fuel Injection Timing - Check".
Note: Install Tooling (A) through the camshaft gear. Install Tooling (B) through the crankshaft web.
Show/hide tableIllustration 1 g00996474 - Install O-ring seal (9) on the fuel injection pump. Position the fuel injection pump on the front housing. Install bolts (12). Tighten the bolts to a torque of
25 N·m (18 lb ft) . - If necessary, install the bolt and bracket (10) on the cylinder block. Tighten the bolt to a torque of
44 N·m (32 lb ft) . - Install bolt (11) and nut (13).
Note: Ensure that the mating surfaces of the fuel injection pump gear and the shaft of the fuel injection pump are clean. Lubricate the threads of the shaft for the fuel injection pump. The nut must turn freely until contact is made with the fuel injection pump gear.
Show/hide tableIllustration 2 g00996413 - Position fuel injection pump gear (8) on the shaft of the fuel injection pump. Install the washer and nut (7). Rotate the fuel injection pump gear in a counterclockwise direction in order to remove the backlash. Tighten nut (7) to a torque of
24 N·m (17 lb ft) .Show/hide tableIllustration 3 g00996409 - Connect the wiring harness assembly to engine shutoff solenoid (4).
- Connect the wiring harness assembly to cold start advance unit (3).
- Connect tube assembly (2) to the fuel injection pump. Connect tube assembly (1) to the fuel injection pump.
Show/hide table
Illustration 4 g00996410 - Loosen bolt (6). Move spacer (5) in order to prevent bolt (6) from tightening against the shaft of the fuel injection pump. Tighten bolt (6) to a torque of
12 N·m (106 lb in) .Note: Spacer (5) must be installed and bolt (6) must be tightened in order to prevent the bolt from contacting the shaft of the fuel injection pump.
Show/hide tableIllustration 5 g00996413 - Tighten nut (7) to a torque of
88 N·m (65 lb ft) . - Remove Tooling (A) and Tooling (B).
End By:
- Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install".
- Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
- Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install".
- Install the air compressor, if equipped. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
Caterpillar Information System:
3054C Industrial Engine Fuel Injection Pump - Remove - Bosch EVPE
C1.5 and C2.2 Generator Rotor - Remove and Install
C1.5 and C2.2 Marine Generator Set Engines Water Pump - Install
G3520B Industrial Engine Throttle Actuator
C1.5 and C2.2 Marine Generator Set Engines Engine Oil Relief Valve - Remove and Install
C1.5 and C2.2 Marine Generator Set Engines Water Pump - Remove
G3304 and G3306 Engines Magneto - Disassemble
G3500 Engines Prelube Pump - Electric
C1.5 and C2.2 Marine Generator Set Engines Exhaust Manifold - Remove and Install
3500B and 3500C Marine Propulsion Engines Synchronizing Switch Not Functioning Properly
2003/05/01 New Front Crankshaft Seals and New Rear Crankshaft Seals are Now in Production {1160, 1161}
2003/05/01 New Front Crankshaft Seals and New Rear Crankshaft Seals are Now in Production {1160, 1161}
C1.5 and C2.2 Marine Generator Set Engines Water Temperature Regulator Housing - Remove and Install
3500 Engines for Caterpillar Built Generator Sets Engine Oil Filter Base
C1.5 and C2.2 Marine Generator Set Engines Expansion Tank - Remove and Install
G3520C and G3520E Generator Set Engines Cylinder Head - Disassemble
G3520C and G3520E Generator Set Engines Cylinder Head - Assemble
C1.5 and C2.2 Marine Generator Set Engines Water Temperature Regulator - Remove and Install
G3500 Engines Prelube Pump - Air
C1.5 and C2.2 Generator Exciter Field - Flash
C27 and C32 Generator Set Engines CID 0100 FMI 10 Engine Oil Pressure Sensor abnormal rate of change
C27 and C32 Industrial and Petroleum Engines CID 0102 FMI 10 Boost Pressure Sensor abnormal rate of change
Product Link 151/201 Installation Examples
3500 Engines for Caterpillar Built Generator Sets Fuel Filter Base