Engine Oil Pump
带平衡器总成的发动机
类型 ... 齿轮驱动差速转子
凸轮数
- 内转子 ... 6
- 外转子 ... 7
Show/hide table
图 1 | g01277444 |
平衡器机油泵 |
(1) 外转子与泵体之间的间隙 ... 0.130 至 0.24 mm (0.0050 至 0.0094 in)
Show/hide table
图 2 | g01277446 |
内转子 |
(2) 内转子与外转子的间隙 ... 0.050 至 0.200 mm (0.0020 至 0.0079 in)
Show/hide table
图 3 | g01277448 |
转子的轴向间隙 |
(3) 转子组件的轴向间隙
- 内转子 ... 0.04 至 0.11 mm (0.0016 至 0.0043
in)
- 外转子 ... 0.04 至 0.00 mm (0.0016 至 0.0043 in)
Show/hide table
图 4 | g01277449 |
端盖 |
(4) 机油泵盖螺栓的扭矩 ... 26 N·m (19 lb ft)
Show/hide table
图 5 | g01277450 |
惰齿轮及泵齿轮 |
注: 更换惰齿轮螺栓 (5) 和机油泵齿轮螺母 (6) 。
(5) 拧紧惰齿轮螺栓至以下扭矩。 ... 26 N·m (19 lb ft)
注: 将发动机置于上止点位置。 请参阅测试和调整, "确定 1 号活塞上止点位置"。 安装平衡器。 请参阅拆解和组装手册。 安装机油泵齿轮并拧紧螺母 (6) 。
(6) 将螺母拧紧至以下扭矩。 ... 95 N·m (70 lb ft)
拧紧将平衡器固定到缸体上的螺栓至以下扭矩。 ... 54 N·m (40 lb ft)
不带平衡器总成的发动机
类型 ... 齿轮驱动差速转子
凸轮数
- 内转子 ... 5
- 外转子 ... 6
Show/hide table
图 6 | g01277453 |
机油泵 |
(7) 外转子与泵体之间的间隙 ... 0.152 至 0.330 mm (0.0059 至 0.0129 in)
Show/hide table
图 7 | g01277455 |
检查间隙 |
(8) 内转子与外转子的间隙 ... 0.040 至 0.127 mm (0.0015 至 0.0050 in)
Show/hide table
图 8 | g01277457 |
检查轴向间隙 |
(9) 转子组件的轴向间隙
- 内转子 ... 0.038 至 0.089 mm (0.0014 至 0.0035
in)
- 外转子 ... 0.025 至 0.076 mm (0.0010 至 0.0029 in)
将紧固机油泵组件前盖的螺栓拧紧至以下扭矩。 ... 26 N·m (19 lb ft)
Caterpillar Information System:
2002/12/01 The Contents Of The Service Manuals For All Commercial Engines Is Available On The Caterpillar Intranet {1000}
3054E Industrial Engine Lifter Group - Remove and Install
2003/08/01 New Flywheels Are Used {1156}
770 and 772 Off-Highway Truck Chassis Electronic Control System Speed Sensor - Adjust
2002/11/01 New Software Helps Eliminate Erroneous Logging Of Diagnostic Codes {7620}
2003/01/01 New Fuel Injector Groups are Used {1254, 1280}
2003/02/01 Some Of The Tees In Some Breather Groups May Be Damaged By Normal Operation {1317}
3056E Industrial Engine Rocker Shaft - Assemble
797 Off-Highway Truck Braking System Visual Inspection
320D Excavator Daily Inspection
C18 Marine Engines Diagnostic Flash Code Retrieval
120H and 135H Motor Graders Machine Systems Circle Drive - Assemble
2003/04/01 Procedure for Tightening the Locknut for the Fan Drive on 3500 Engines {1359}
2003/02/01 New Turbocharger Oil Lines Group is Now Available {1052}
2003/02/01 A New Cylinder Head Gp For G3412 Engines {1101}
2003/04/01 New Water Pumps for 3500 Engines {1361, 1389}
2003/02/10 Use the Correct Accessory Drive Shaft with the Cage Assembly {1207}
3056E Industrial Engine Camshaft - Remove and Install
2003/03/01 New Cylinder Head Groups and New Prechamber Groups With 1/2-13 Standard Bolts Are Available {1100}
2003/01/01 Spacer Installation is Now Recommended for Improved Oil Control on 3100 Camshaft Housing Covers {1210}
2003/01/06 Spacer Installation is Now Recommended for Improved Oil Control on 3100 Camshaft Housing Covers {1210}
G3408C and G3412C Engines Valve Mechanism
2002/11/01 The New 213-9285 Valve Recession Tool Kit Is Available {0703}
C18 Generator set and C18 Marine Engines Alternator - Remove and Install