Summary of Revisions
Information Changes
The following table summarizes the major changes in this manual:
Show/hide table
| Titles | Description of Change |
| Revision 01 | |
| "Fuel Filter Base - Remove" | Tooling (A) |
| "Fuel Filter Base - Install" | Tooling (A) |
| "Electronic Unit Injector - Install" | Tooling (A) |
| "Electronic Unit Injector Sleeve - Remove" | Tooling (A) |
| "Electronic Unit Injector Sleeve - Install" | Tooling (B) Tooling (D) |
| "Turbocharger - Install" | Tooling (A) |
| "Exhaust Manifold - Remove and Install" | Tooling (A) for Installation Procedure Tooling (B) for Installation Procedure |
| "Inlet and Exhaust Valve Seat Inserts - Remove and Install" | Tooling (A) |
| "Engine Oil Filter Base - Remove" | Tooling (A) |
| "Engine Oil Filter Base - Install" | Tooling (A) |
| "Engine Oil Cooler - Disassemble" | Tooling (A) |
| "Water Pump - Assemble" | Procedure Tooling (D) |
| "Flywheel - Remove" | Tooling (A) |
| "Flywheel - Install" | Procedure Tooling (A) Tooling (B) |
| "Crankshaft Rear Seal - Install" | Tooling (E) Tooling (F) |
| "Vibration Damper and Pulley - Remove and Install" | Tooling (A) for Installation Procedure |
| "Crankshaft Front Seal - Install" | Tooling (E) Tooling (F) |
| "Gear Group (Front) - Install" | Tooling (A) Tooling (B) |
| "Valve Mechanism Cover Base - Remove and Install" | Tooling (A) for Installation Procedure |
| "Cylinder Head - Install" | Tooling (A) Tooling (B) Tooling (C) |
| "Camshaft - Install" | Tooling (F) Tooling (G) |
| "Camshaft Bearings - Remove" | Procedure |
| "Camshaft Bearings - Install" | Procedure |
| "Connecting Rod Bearings - Install" | Tooling (B) |
| "Fan Drive - Assemble" | Tooling (B) |
| "Electronic Control Module - Remove and Install" | Procedure |
| "Alternator - Remove and Install" | Procedure |
| "Electric Starting Motor - Remove and Install" | Procedure |
| "Air Compressor - Remove and Install" | Tooling (A) |
Caterpillar Information System:
G3500B Engines Engine Governing - Adjust
G3520C and G3520E Generator Set Engines General Information (Electronic Control System)
2002/11/04 Connecting Rods with Dual Bearing Tab Slots are OK to Use {1218}
C4.4 (Mech) Industrial Engine Lubrication System
C4.4 (Mech) Industrial Engine Cooling System
2002/10/01 Parts Manuals For The Following Engines Are Now Provided On A CD-ROM {1000, 7000}
2002/11/01 A New Water Tank Group Is Used To Contain The Overflow Of Coolant {1354, 1377}
Product Link 151/201 Reporting Interval Erratic
Product Link 151/201 Operating Hours Discrepancy
Product Link 151/201 Diagnostics and Events Not Available
3054E Industrial Engine Air Inlet and Exhaust System
Product Link 151/201 Position Reports Not Available
G3520C and G3520E Generator Set Engines Manifold Air Pressure Sensor
3054E Industrial Engine Electrical System
G3606 and G3608 Engines Crankshaft Main Bearings - Remove
G3520C and G3520E Generator Set Engines Detonation Sensor
G3520C and G3520E Generator Set Engines Ignition Transformer
3054E Industrial Engine Fuel Injection
3054C Industrial Engine Fuel Related Components in Cold Weather
3054E Industrial Engine Electronic Control System
3516B Generator Set Engines with Dynamic Gas Blending General Information (Fuel System) - Gas
3054C Industrial Engine Refill Capacities
C9 Marine Engines and C9 Marine Generator Sets Heat Exchanger
C7 Urban Transit Bus Engines Fire Prevention and Explosion Prevention