Fuel Control Valve - Remove and Install
Show/hide table
| 注意 |
|---|
|
在检查、保养、测试、调整及维修产品时，请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前，请准备好盛接液体用的适当容器。 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 确保已断开供油。
- 断开进油接头 (6)。
- 拆下螺栓 (1)。 从控油阀的轴的端部卸下 U 形夹 (2)。
- 卸下锁紧螺母 (3)。
- 支起控油阀 (4)，然后卸下螺栓 ( 5)。
- 拆下燃油控制阀。
Show/hide table
| |
| 图 1 | g00868297 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
| 注意 |
|---|
|
在检查、保养、测试、调整及维修产品时，请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前，请准备好盛接液体用的适当容器。 |
- 安装控油阀 (4)。
- 安装螺栓 (5)。
- 安装锁紧螺母 (3)。
- 安装 U 形夹 (2) 和螺栓 ( 1)，将连接件连接至控油执行器。
- 连接进油接头 (6)。
Show/hide table
|
| |
| 图 2 | g00868297 |
Caterpillar Information System:
3618 Engine Thermocouple - Test - Main Bearings' Thermocouples
3500 Industrial Engines Vacuum Gauge
3618 Engine Particle Detector - Test
3618 Engine Oil Mist Detector - Test
3618 Engine Oil Pressure Transducer - Test - Shutdown for Low Engine Oil pressure
3500 Generator Set Engines Pressure Gauge - Engine Oil
2002/03/11 Correction to Information Regarding the Need for Timing Calibration after Replacing the Engine ECM {1901, 1912, 1912}
3500 Industrial Engines Differential Pressure Gauge
3500 Generator Set Engines Pressure Gauge
3054 and 3056 Industrial and Generator Set Engines Vibration Damper and Pulley
3618 Engine Engine Speed Switch - Test
N3 Series Brushless Alternators Rectifier - Test
3500 Generator Set Engines Pressure Gauge - Hydraulic Oil
2002/03/01 A New Service Manual, RENR5971, "System Operation And Programming Guides For Digital Governor Control Used On 3618 Engine" Is Available {1908}
3500 Generator Set Engines Temperature Gauge
G3612 and G3616 Engines Spark Plugs - Remove and Install
G3612 and G3616 Engines Detonation Sensor - Remove and Install
3500 Generator Set Engines Temperature Gauge
3618 Engine Transducer - Calibrate
3406E, C12, C15 and C18 Marine Engines Sensors and Electrical Connectors
3406E, C12, C15 and C18 Marine Engines Analog Sensor Supply Circuit - Test
3406E, C12, C15 and C18 Marine Engines Electrical Power Supply Circuit - Test
N3 Series Brushless Alternators Stator - Test
G3612 and G3616 Engines Fuel Lines - Remove and Install