Track Adjuster
Show/hide table
Illustration 1 | g00860304 |
(1) Apply a thin coat of 2P-9065 Lubricant to the bore and to the seal groove in the cylinder.
(2) Assemble the rings and seals so that each brown ring is installed between a black ring and a seal.
(3) Apply a thin coat of 2P-9065 Lubricant to the outer diameter and to the seal grooves of the piston assembly.
(4) Tighten the valves to a torque of 34 ± 5 N·m (25 ± 4 lb ft).
(5) Fill the hole with 2P-9065 Lubricant.
(6) No air is allowed in this area after assembly.
(7) Dimension for installation of the seal ... 0.5 ± 0.5 mm (0.02 ± 0.02 inch)
Caterpillar Information System:
C7 and C9 On-Highway Engines Ignore Brake/Clutch Switch Circuit - Test
3126B and 3126E On-highway Engines Intermittent Cruise Control, Idle, or PTO Kickout
325C Excavator Machine System Specifications Recoil Spring
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Recoil Spring
3126B and 3126E On-highway Engines Cruise Control, Idle, or PTO Can Not Be Set
C12 Marine Engine Cooling System - Test
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Front Idler
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Install
3126E Truck Engine Fan Drive Mounting Group
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Remove
3126E On-highway Engine Service Brake Pedal Position (Switch 2) Circuit - Test
C7 and C9 On-Highway Engines Service Brake Pedal Position (Switch 1) Circuit - Test
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Track Roller (Single Flange)
2002/02/01 Correction To Disassembly and Assembly Module, SENR5535-04, "G3612 and G3616 Engines" , "Cylinder Head - Remove" {1100}
G3612 and G3616 Engines Engine Support - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Disassemble
318C and 319C Excavators Machine System Specifications Track Roller (Single Flange)
2002/05/01 New Starting Motors Used {1453}
CPT372 Truck Mounted Pumper Control Panel
2002/02/01 A New Systems Operation/Testing And Adjusting Module, RENR5889, "Standby Pump Panel" Is Available {0758}
C7 and C9 On-Highway Engines Powertrain Data Link Circuit - Test
3512B Engine for SPF343, SPS343, and SPT343 Pumpers CAT Data Link
3054, 3054B and 3056 Marine Engines Rocker Shaft and Pushrod - Remove
2002/02/01 New Special Instruction, REHS1178, "Operating Instructions For The 4P-4788 Electrical Converter Gp And The 4P-4789 Electrical Converter Gp" Is Available {1421}