Fan Drive Mounting Group
One-Piece Fan Drive Mounting Group (If Equipped)
Show/hide table
Illustration 1 | g01155558 |
(1) Screw (2) Bolt (3) Bolt |
Note: The front lifting bracket for the engine is located behind the fan drive mounting group. The engine lifting bracket is secured with the hardware for the fan drive mounting group.
- Assemble the fan drive mounting group to the engine. Tighten bolt (2) finger tight.
- Tighten bolt (3) finger tight.
- Tighten screw (1) into the water regulator housing finger tight.
- Tighten the front primary bolt (2) to a torque of 55 ± 10 N·m (40 ± 7 lb ft).
- Tighten bolt (3) to a torque of 28 ± 7 N·m (20 ± 5 lb ft).
- Tighten remaining hardware to a torque of 28 ± 7 N·m (20 ± 5 lb ft).
Two-Piece Fan Drive Mounting Group (If Equipped)
Show/hide table
Illustration 2 | g01155465 |
Installation of the fan drive mounting support assembly only
- Install the support assembly (5) to the fan drive mounting group (2). Tighten bolt (6) to a torque of 28 ± 7 N·m (20 ± 5 lb ft).
- Tighten bolt (4) to a torque of 55 ± 10 N·m (40 ± 7 lb ft).
- Tighten the remaining hardware for the support assembly to a torque of 28 ± 7 N·m (20 ± 5 lb ft).
Installation of the entire fan drive mounting
Note: The front lifting bracket for the engine is located behind the fan drive mounting group. The engine lifting bracket is secured with the hardware for the fan drive mounting group.
- Assemble the engine lifting bracket and the fan drive mounting to the engine.
- Tighten the front bolt (3) finger tight.
- Tighten screw (6) finger tight.
- Tighten bolt (6) to a torque of 28 ± 7 N·m (20 ± 5 lb ft).
- Tighten bolt (4) finger tight.
- Tighten the front bolt (3) to a torque of 55 ± 10 N·m (40 ± 7 lb ft).
- Tighten the bolt (4) to a torque of 55 ± 10 N·m (40 ± 7 lb ft).
- Tighten remaining hardware to a torque of 28 ± 7 N·m (20 ± 5 lb ft).
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Remove
3126E On-highway Engine Service Brake Pedal Position (Switch 2) Circuit - Test
C7 and C9 On-Highway Engines Service Brake Pedal Position (Switch 1) Circuit - Test
3126B and 3126E On-highway Engines PTO Switch Circuit - Test
C7 and C9 On-Highway Engines Neutral Switch Circuit - Test
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive
CPT372 Truck Mounted Pumper Cooling System Coolant Level - Check
2012/08/28 Caterpillar's Position On The Use Of Biodiesel Fuel In Caterpillar Engines {1000}
2002/03/01 A New Engine Oil Grade Plug 0W20 Is Now Available {1408}
3500 Industrial Engines Restriction of Air Inlet and Exhaust
2002/01/01 Caterpillar's Position On The Use Of Biodiesel Fuel In Caterpillar Engines {1000}
3126 Truck Engine Military Water Temperature Regulator - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Front Idler
C12 Marine Engine Cooling System - Test
3126B and 3126E On-highway Engines Cruise Control, Idle, or PTO Can Not Be Set
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Recoil Spring
325C Excavator Machine System Specifications Recoil Spring
3126B and 3126E On-highway Engines Intermittent Cruise Control, Idle, or PTO Kickout
C7 and C9 On-Highway Engines Ignore Brake/Clutch Switch Circuit - Test
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Adjuster
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Track Roller (Single Flange)
2002/02/01 Correction To Disassembly and Assembly Module, SENR5535-04, "G3612 and G3616 Engines" , "Cylinder Head - Remove" {1100}
G3612 and G3616 Engines Engine Support - Remove and Install