Front Idler
Show/hide table
Illustration 1 | g00101229 |
(1) Remove plug (1) from Front Idler Assembly and apply air pressure to this port. Front Idler Assembly should sustain 255 ± 10 kPa (37 ± 1.5 psi) air pressure for a minimum of 30 seconds. Add 0.26 L (.07 US gal) of SAE 30-D oil and replace plug (1).
(2) At assembly, O-rings of floating seal (2) must be clean and dry. Apply a small amount of oil on the contacting surfaces of the metal seals before installation.
(3) Apply a small amount of oil on seal.
(4) Install the pin. The correct position of the pin is shown in View A-A.
(5) Install the shaft (5). Position the "R" that is stamped on the end face backward into the angular bearing.
End play:
- Minimum ... 0.25 mm (.010 inch)
- Maximum ... 1.15 mm (.045 inch)
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Install
3126E Truck Engine Fan Drive Mounting Group
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Remove
3126E On-highway Engine Service Brake Pedal Position (Switch 2) Circuit - Test
C7 and C9 On-Highway Engines Service Brake Pedal Position (Switch 1) Circuit - Test
3126B and 3126E On-highway Engines PTO Switch Circuit - Test
C7 and C9 On-Highway Engines Neutral Switch Circuit - Test
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive
CPT372 Truck Mounted Pumper Cooling System Coolant Level - Check
2012/08/28 Caterpillar's Position On The Use Of Biodiesel Fuel In Caterpillar Engines {1000}
2002/03/01 A New Engine Oil Grade Plug 0W20 Is Now Available {1408}
3500 Industrial Engines Restriction of Air Inlet and Exhaust
C12 Marine Engine Cooling System - Test
3126B and 3126E On-highway Engines Cruise Control, Idle, or PTO Can Not Be Set
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Recoil Spring
325C Excavator Machine System Specifications Recoil Spring
3126B and 3126E On-highway Engines Intermittent Cruise Control, Idle, or PTO Kickout
C7 and C9 On-Highway Engines Ignore Brake/Clutch Switch Circuit - Test
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Adjuster
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Track Roller (Single Flange)
2002/02/01 Correction To Disassembly and Assembly Module, SENR5535-04, "G3612 and G3616 Engines" , "Cylinder Head - Remove" {1100}
G3612 and G3616 Engines Engine Support - Remove and Install
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Disassemble
318C and 319C Excavators Machine System Specifications Track Roller (Single Flange)