Heat Exchanger - Remove - 3054 and 3054B Engines
Removal Procedure
Start By:
- Drain the cooling system. If the engine uses diesel engine antifreeze/coolant, refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change". If the engine uses extended life coolant, refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
- Drain the sea water circuit. Refer to Operation and Maintenance Manual, "Sea Water Strainer - Clean/Inspect" for more information.
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (1) and remove manual sump pump (2) .
Show/hide table
 | |
| Illustration 1 | g00799722 |
- Remove hose (3) from heat exchanger (9).
Show/hide table
 | |
| Illustration 2 | g00799696 |
- Loosen hose clamp (4) from hose (5).
- Loosen hose clamps (6) and remove hose (7) from heat exchanger (9) .
- Loosen hose clamp (8) .
- Loosen hose clamps (10) and loosen hose clamps (11). Remove the hoses from heat exchanger (9) .
Show/hide table
 | |
| Illustration 3 | g00799713 |
- Remove bolts (14) that secure heat exchanger (9) to the engine. Remove the heat exchanger from the engine.
Show/hide table
 | |
| Illustration 4 | g00799733 |
Caterpillar Information System:
Electronic Modular Control Panel II+ (EMCP II+) Starting Motor Magnetic Switch - Test
3512B Marine Auxiliary Engine System Overview
G3520C and G3520E Engines Water Temperature Regulator
120H and 135H Motor Graders Alternate Exit
G3600 Engines Engine Speed/Timing Sensor - Clean/Inspect
3054 and 3056 Industrial and Generator Set Engines Fuel System - Prime
3034 Marine Engine - Installation Guide Engine Mounting
3500B and 3500B High Displacement Generator Set Engines Engine Control Switch (ECS) (EMCP II)
Electronic Modular Control Panel II+ (EMCP II+) Instrument Panel
3054, 3054B and 3056 Marine Engines Fuel Injection Pump - Install - Delphi
3054, 3054B and 3056 Marine Engines Fuel Injection Pump - Remove - Delphi
3054, 3054B and 3056 Marine Engines Engine Oil Filter Base - Install - 3056 Engine
3034 Marine Engine Fuel System Secondary Filter - Replace
Electronic Modular Control Panel II (EMCP II) GSC CID 0441 - FMI 12 (for MUI Engines)
797 Off-Highway Truck Power Train Final Drive - Assemble
3054, 3054B and 3056 Marine Engines Heat Exchanger - Install - 3054 and 3054B Engines
3054, 3054B and 3056 Marine Engines Heat Exchanger - Disassemble - 3054 and 3054B Engines
3054, 3054B and 3056 Marine Engines Heat Exchanger - Assemble - 3054 and 3054B Engines
2001/07/01 New Hydrax Electronic Control Is Available {1900}
EMCPII+ for Gas Engines Starting Motor Magnetic Switch - Test - 3500 Engines Only
2001/06/01 Change to the Torque of the Adjusting Screw Locknut for the Unit Injector (Specifications Manuals) {1290}
2001/06/01 Change to the Torque of the Adjusting Screw Locknut for the Unit Injector (Testing and Adjusting Manuals) {1290}
Electronic Modular Control Panel II+ (EMCP II+) Shutdown Mode - PEEC and EUI Engines
Electronic Modular Control Panel II+ (EMCP II+) Shutdown Mode - MUI Engines