Gas Pressure Regulator - Assemble
组装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 膜片组件 (26) 由弹簧 (28) 、弹簧座 (29) 、挡圈 (30) 、弹簧座 (31) 、挡圈 (32) 和轴 (33) 组成。
Show/hide table
图 1 | g00782733 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 将弹簧 (25) 安装到调节器体 (4) 中。
Show/hide table
图 2 | g00782723 |
- 安装三颗螺钉 (24) 和膜片组件 (26) 。
- 将塑料衬套 (23) 安装在气门组件 (8) 中。
Show/hide table
图 3 | g00782719 |
- 将橡胶膜片 (21) 和垫圈 (22) 安装在轴 (20) 上。
Show/hide table
图 4 | g00782714 |
- 将轴 (20) 安装到气门组件 (8) 中。
Show/hide table
图 5 | g00782712 |
- 将挡圈 (19) 安装到轴 (18) 上。
Show/hide table
图 6 | g00782708 |
Show/hide table
图 7 | g00782704 |
- 将轴 (18) 安装到轴 (20) 上。 安装定位销 (17) 。
- 将弹簧垫圈 (15) 和 O 形密封圈 (16) 安装到气门 (14) 上。
Show/hide table
图 8 | g00782698 |
- 将气门 (14) 安装到气门组件 (8) 上。
Show/hide table
图 9 | g00782694 |
- 将气门头 (11) 、塑料垫圈 (12) 和金属垫圈 (13) 安装到气门组件 (8) 上。
Show/hide table
图 10 | g00782670 |
- 将自锁紧螺母 (10) 安装到气门组件 (8) 上。
Show/hide table
图 11 | g00782662 |
- 安装气门组件 (8) 和 O 形密封圈 (10) 。 固定两颗螺钉 (9) 。
Show/hide table
图 12 | g00782658 |
- 安装 O 形密封圈和适配器密封圈 (7) 。
Show/hide table
图 13 | g00782590 |
- 将板 (6) 安装到调节器体 (4) 上。
Show/hide table
图 14 | g00782584 |
- 将膜片组件 (3) 安装到调节器体 (4) 上。 固定螺母 (5) 。
Show/hide table
图 15 | g00782579 |
- 将气体压力调节器放在一起。 固定螺栓 (2) 、螺母和垫圈。
Show/hide table
图 16 | g00782565 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 安装适配器 (1) 。
Show/hide table
图 17 | g00782543 |
End By: 安装气体压力调节器。 请参阅 拆解和组装, "机气体压力调节器 - 安装"。
Caterpillar Information System:
3412C Engine Fuel Filter Base
C-9 Industrial Engine Fan Drive - Remove
3412C Engine Engine Oil Filter
PM3516 Power Modules Control Panel
PM3516 Power Modules Alarms and Shutoffs
3126B Engine for Caterpillar Built Machines Injection Actuation Pressure Control Valve Circuit - Test
G3408C and G3412C Engines Gas Pressure Regulator - Disassemble
3412C Engine Engine Oil Filter Base
G3408C and G3412C Engines Gas Pressure Regulator - Install
G3408C and G3412C Engines Gas Pressure Regulator - Remove
3064 and 3066 Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
C9 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
2001/04/01 New Seventeen Character Product Identification Number (PIN) {7557}
G3408C and G3412C Engines Governor Drive - Remove
G3408C and G3412C Engines Governor - Remove and Install
2001/04/01 New Air Shutoff Groups Are Used {1078}
Exhaust Temperature Scanner Worksheet
G3408C and G3412C Engines Governor Drive - Install
3412C Engine Valve Mechanism Cover
C-9 Industrial Engine Fan Drive - Install
3412C Engine Turbocharger
3412C Engine Turbocharger Oil Lines
G3408C and G3412C Engines Governor Drive - Disassemble
3126B Engine for Caterpillar Built Machines Engine Speed/Timing Sensor - Calibrate