Fuel Transfer Pump - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 8T-2998     | 润滑剂     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 有关输油泵部件的可再用性信息,请参阅再使用零件和修补操作指南, SEBF8434, "3100 调速器检查和概述(机械调速器总成,用于配备机械式单体喷油器(MUI)的 3114、3116 和 3126 发动机)"。
- 用清洁的发动机机油润滑接头 (10) 和孔。 安装单向阀和接头 (10) 。
Show/hide table
图 1 | g00623719 |
- 检查 O 形密封圈的状况。 必要时,应更换 O 形密封圈。 安装下部 O 形密封圈 (9) 。
Show/hide table
图 2 | g00623714 |
- 将工具 (A) 涂敷在挺杆 (8) 的端面上。 安装套筒组件 (7) 。 确保套筒的平面与壳体孔的平面对准。
- 用清洁的发动机机油润滑活塞 (5) 。 安装活塞 (5) 和弹簧 (4) 。
Show/hide table
图 3 | g00623687 |
- 用清洁的发动机机油润滑接头 (3) 和安装单向阀的孔。 安装单向阀,使密封表面朝向接头。
Show/hide table
图 4 | g00623686 |
- 安装 O 形密封圈和接头 (3) 。
- 将盖 (1) 安置在弹簧 (4) 上。 安装螺栓 (2) 以压缩弹簧 (4) 。
Show/hide table
图 5 | g00623671 |
Show/hide table
图 6 | g00623633 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
Caterpillar Information System:
G3408 and G3412 Engines Cylinder Head
G3408C and G3412C Engines Cylinder Head
3126B Industrial Engine Alternator and Regulator
C9 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
2001/04/01 New Two-Stage Choke Assembly Linkage Is Introduced {1071}
G3408C and G3412C Engines Valve Mechanism
3126B Industrial Engine Front Housing and Covers
C9 Engine For Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
3054, 3054B and 3056 Marine Engines Aftercooler - Install
3126B Industrial Engine Fan Drive
G3408C and G3412C Engines Engine Design
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Transfer Pump
3114, 3116, and 3126 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
3608 Engine Specifications
G3408 and G3412 Engines Exhaust Manifold - Water Cooled
3126B and 3126E Truck Engines Engine Oil Temperature Sensor
3054E and 3056E Industrial Engines Stopping the Engine
C9 Engine For Caterpillar Built Machines Cylinder Block Cover - Remove and Install
3500B Industrial Engines Engine Sensor Open/Short Test
3054, 3054B and 3056 Marine Engines Aftercooler - Disassemble
3608 Engine Tools
G3408 and G3412 Engines Valve Cover
320E and 323E Excavators VA Boom Controls - If Equipped
3054, 3054B and 3056 Marine Engines Aftercooler - Assemble