Rocker Shaft - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 6V-0083     | 金刚砂抛光纸     | 1     |
开始:
- 拆下摇臂轴组件和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 有关摇臂轴部件的可再用性信息,请参阅再使用零件和修补操作指南, SEBF8267, "3114 和 3116 发动机的摇臂和摇臂轴"。
- 从摇臂轴组件 (4) 上拆下支架 (1) 。
Show/hide table
图 1 | g00629612 |
- 从摇臂轴组件 (4) 上拆下气门摇臂 (2) 和单体喷油器摇臂 (3) 。
注: 不要从摇臂轴组件推动摇臂。 如有必要,用一片工具 (A) 轻轻擦亮轴的表面以辅助拆卸。
- 检查气门摇臂 (2) 和单体喷油器摇臂 (3) 上的调整螺钉有无损坏。
- 检查摇臂轴组件 (4) 有无擦伤和裂纹。
- 检查单体喷油器摇臂 (3) 上的轴承 (5) 。 摇臂上的孔径为 24.808 ± 0.20 mm (0.9767 ± 0.0079 in)。 请参阅技术规格, "气门摇臂和挺杆"。 如有必要,更换轴承。
Show/hide table
图 2 | g00630277 |
- 确保单体喷油器摇臂 (3) 上的按钮 (6) 没有损坏。 还要确保按钮 (6) 的挡圈就位。
Caterpillar Information System:
3054, 3054B and 3056 Marine Engines Heat Exchanger - Install - 3056 Engine
3054, 3054B and 3056 Marine Engines Heat Exchanger - Assemble - 3056 Engine
G3500B Engines Engine Monitoring System
3054, 3054B and 3056 Marine Engines Heat Exchanger - Disassemble - 3056 Engine
Electronic Modular Control Panel II (EMCP II) Schematics and Wiring Diagrams
3114, 3116, and 3126 Engines for Caterpillar Built Machines Governor - Remove
G3406 Engines Gear Group (Front)
3114, 3116, and 3126 Engines for Caterpillar Built Machines Governor - Install
G3406 Engines Cylinder Block
C7 Marine Engine Closed Crankcase Ventilation (CCV) Fumes Disposal Filter - Replace
3176C and 3196 Marine Engines Marine Power Display
G3406 Engine Turbocharger - Inspect
C12 Marine Engines Closed Crankcase Ventilation (CCV) Filter Service Indicator - Inspect
3054 and 3056 Marine Generator Set Engines Auxiliary Water Pump - Remove
3406E Engine Engine Oil Filter Base - Disassemble - Engine without BrakeSaver
Electronic Modular Control Panel II (EMCP II) Troubleshooting Diagnostic Codes
3406E Engine Engine Oil Filter Base - Assemble - Engine without BrakeSaver
3500B Industrial Engines with the ADEM 3 Electronic Control Module Electronic Display Module - Optional
3126B Industrial Engine Fuel Transfer Pump - Remove
3126B Industrial Engine Fuel Transfer Pump - Install
3054 and 3056 Marine Generator Set Engines Auxiliary Water Pump - Install
3406E Engine Engine Oil Cooler - Remove
Electronic Modular Control Panel II (EMCP II) Starting Motor Magnetic Switch - Test - 3306B and 3406C MUI Engines
Electronic Modular Control Panel II (EMCP II) Starting Motor Magnetic Switch - Test - EUI Engines Only