3114, 3116, and 3126 Engines for Caterpillar Built Machines Caterpillar


Governor - Install

Usage:

IT38G 1CW

安装步骤

表 1
所需工具    
工具     零件号     零件描述     数量    
A     136-4149     调速器钳 (1)     1    
B     128-8827     销 (1)     1    
1U-7523 销导向器 (1)     1    
( 1 ) 该工具属于 128-8822 调速器工具总成 。


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。


注: 有关调速器的更详细信息,请参阅维修手册, SENR6454, "3114、3116 和 3126 发动机调速器"。 维修手册, SENR6454 要求使用 1U-7326 调速器标定试验台 。 有关调速器部件的可再用性信息,请参阅再使用零件和修补操作指南, SEBF8434, "3100 调速器检查和概述(机械调速器总成,用于配备机械式单体喷油器(MUI)的 3114、3116 和 3126 发动机)"。




    图 1g00673178

  1. 将润滑剂涂在新的 O 形密封圈 (1) 上。 将新的 O 形密封圈 (1) 安装在缸盖中。



    图 2g00672733

  1. 将润滑剂涂在新的 O 形密封圈 (2) 上。 将新的 O 形密封圈 (2) 安装在管组件 (5) 上。



    图 3g00672742

  1. 将 O 形密封圈和管组件 (5) 安装在缸盖中。



    图 4g00673180

  1. 将润滑剂涂在新的 O 形密封圈 (3) 上。 将新的 O 形密封圈 (3) 安装在调速器上。



    图 5g00673182

  1. 将调速器在发动机上正确就位。



    图 6g00613563

  1. 安装将调速器固定到位的垫圈和螺栓 (7) 。



    图 7g00672755

  1. 将 U 形夹销 (6) 安装在工具 (B) 中。



    图 8g00672752

  1. 使用工具 (B) 安装 U 形夹销 (6) 和夹子。

  1. 检查燃油设置调整情况。 请参阅测试和调整, SENR5118。



    图 9g00655975

  1. 使用工具 (A) 将管组件 (5) 滑到调速器内。



    图 10g00613071

  1. 安装夹子 (4) 。



    图 11g00613041

  1. 安装机油管组件 (1) 。 安装管组件 (2) 和空燃比控制管组件 (3) ,如有配备。 塞住并盖住所有接头。

  1. 安装调速器控制电缆。

End By: 安装燃油切断电磁阀。 请参阅 拆解和组装, "燃油切断电磁阀 - 拆卸和安装"。

Caterpillar Information System:

G3406 Engines Cylinder Block
C7 Marine Engine Closed Crankcase Ventilation (CCV) Fumes Disposal Filter - Replace
3176C and 3196 Marine Engines Marine Power Display
G3406 Engine Turbocharger - Inspect
3054, 3054B and 3056 Marine Engines Heat Exchanger - Remove - 3056 Engine
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Exhaust Manifold
PM3412C Power Modules Maintenance Interval Schedule
PM3412C Power Modules Refill Capacities
3054, 3054B and 3056 Marine Engines Fuel Filter Base - Remove and Install - 3056 Engine
G3406 Engine Gas Pressure
PM3412C Power Modules Safety Signs and Labels
2000/10/02 Repair Parts Available for Alternator R-Terminal {1405}
G3406 Engines Gear Group (Front)
3114, 3116, and 3126 Engines for Caterpillar Built Machines Governor - Remove
Electronic Modular Control Panel II (EMCP II) Schematics and Wiring Diagrams
3054, 3054B and 3056 Marine Engines Heat Exchanger - Disassemble - 3056 Engine
G3500B Engines Engine Monitoring System
3054, 3054B and 3056 Marine Engines Heat Exchanger - Assemble - 3056 Engine
3054, 3054B and 3056 Marine Engines Heat Exchanger - Install - 3056 Engine
3126 Truck Engine Military Rocker Shaft - Disassemble
C12 Marine Engines Closed Crankcase Ventilation (CCV) Filter Service Indicator - Inspect
3054 and 3056 Marine Generator Set Engines Auxiliary Water Pump - Remove
3406E Engine Engine Oil Filter Base - Disassemble - Engine without BrakeSaver
Electronic Modular Control Panel II (EMCP II) Troubleshooting Diagnostic Codes
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.