Rotator Head Bolts - Inspect
- Stop the machine engine in order to prevent inadvertent movement of the work tool.
Note: The host machine must be equipped with a boom lowering control valve in order to perform this procedure. If the host machine is not equipped with a boom lowering control valve, contact your Verachtert dealer.
- Check the rotator head bolts (2) on the outer ring (1). If any bolts are missing the heads, replace all the bolts (2) in the outer ring (1) .
ReferenceFor more information on replacing the rotator head bolts, refer to Operation and Maintenance Manual, "Rotator Head Bolts - Replace" for the work tool that is being serviced.
Show/hide table
 | |
| Illustration 1 | g02174758 |
- Remove bolts (5) and washers (4). Remove cover plate (3) .
Show/hide table
 | |
| Illustration 2 | g02174775 |
- Cover plate (3) must be removed in order to access rotator head bolts (6) in the inner ring (7). Only a few bolts will be accessible at a time.
Show/hide table
 | |
| Illustration 3 | g02190813 |
- Check rotator head bolts (6) in the inner ring (7). If any bolts are missing the heads, replace all the bolts (6) in the inner ring (7) .
Note: The work tool can be rotated manually in order to view all of the rotator head bolts. Use a sufficiently long lever in order to rotate the work tool.
ReferenceFor more information on replacing the rotator head bolts, refer to Operation and Maintenance Manual, "Rotator Head Bolts - Replace" for the machine that is being serviced.
- Install cover plate (3) .
- Install washers (4) and bolts (5) .
Caterpillar Information System:
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Check
C4.2 and C6.4 Engines for Caterpillar Built Machines Air in Fuel - Test
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Jaw - Repair
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Hub Nut - Check/Tighten
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Gear and Bearing - Lubricate
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Cutting Edge Bolts - Tighten
Caterpillar Monitoring System Service Tools
The Replacement Procedure for the Hydraulic Cylinder Assembly on Certain Shears{5553} The Replacement Procedure for the Hydraulic Cylinder Assembly on Certain Shears{5553}
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Cutters - Inspect/Replace
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Bushings - Lubricate
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Reference Material
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Lifting and Tying Down
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Replace
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Wear Plates - Inspect/Replace
390D Excavator Hydraulic System Relief Valve (Swing)
Failure of the Alternator on Certain 320D, 321D CR and 323D Excavators{1405} Failure of the Alternator on Certain 320D, 321D CR and 323D Excavators{1405}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Tank - Remove and Install
Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120} Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120}
Installation Procedure for 306-8313 Auxiliary Control Wiring Gp {1408} Installation Procedure for 306-8313 Auxiliary Control Wiring Gp {1408}
S365C and S385C Work Tools Hydraulic Cylinder
2010/09/30 A New Final Drive Group and Motor Housing is Now Used On 385C Excavators {4050}
Installation Procedure for the 338-6188 Front Lines Gp {5057} Installation Procedure for the 338-6188 Front Lines Gp {5057}
2011/01/20 New Parts are Used To Stabilize the Hydraulic Pressure on 330D Excavators and Mobile Hydraulic Power Units {5069, 5070, 5117}
390D Excavator Hydraulic System Pilot Valve (Swing Parking Brake)