Gear and Bearing - Lubricate
Show/hide table
Illustration 1 | g01736094 |
VHS-60/4 |
Show/hide table
Illustration 2 | g01736198 |
VHS-70/4 |
Note: Clean the fittings before you lubricate the fittings in order to prevent contamination.
- Lubricate fittings (2) for the gear and the bearing with 2 to 3 pumps of grease.
- Rotate the shear for 90 degrees. Repeat steps 1 and 2.
- Repeat steps 1 through 3 three times. The shear must be rotated 90 degrees when lubricant is added to the fittings (1) and (2) .
- Rotate the shear for an additional 90 degrees in order to distribute the grease evenly.
Refer to Operation and Maintenance Manual, "General Maintenance Information" for lubrication information.
Caterpillar Information System:
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Cutting Edge Bolts - Tighten
Caterpillar Monitoring System Service Tools
The Replacement Procedure for the Hydraulic Cylinder Assembly on Certain Shears{5553} The Replacement Procedure for the Hydraulic Cylinder Assembly on Certain Shears{5553}
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Cutters - Inspect/Replace
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Bushings - Lubricate
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Reference Material
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Lifting and Tying Down
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Transport Position
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600} NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Operation
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Daily Inspection
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Work Tool Installation and Removal
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Hub Nut - Check/Tighten
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Jaw - Repair
C4.2 and C6.4 Engines for Caterpillar Built Machines Air in Fuel - Test
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Check
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Inspect
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Replace
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Wear Plates - Inspect/Replace
390D Excavator Hydraulic System Relief Valve (Swing)
Failure of the Alternator on Certain 320D, 321D CR and 323D Excavators{1405} Failure of the Alternator on Certain 320D, 321D CR and 323D Excavators{1405}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Tank - Remove and Install
Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120} Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120}
Installation Procedure for 306-8313 Auxiliary Control Wiring Gp {1408} Installation Procedure for 306-8313 Auxiliary Control Wiring Gp {1408}