Hydraulic Tank - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Brackets     | 4     |
B     | -     | Loctite 271     | -     |
C     | -     | Loctite 242     | -     |
Start By:
- Release the hydraulic system pressure.
- Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining and filling procedures.
- Remove cover assembly (2) .
Show/hide table
Illustration 1 | g02211633 |
- Use two people in order to remove cover assembly (3) . The weight of cover assembly (3) is approximately 28 kg (62 lb). Remove bolts (1) and cover assembly (3) .
- Remove bolts (4) and gauge assembly (6) .
Show/hide table
Illustration 2 | g02211634 |
- Disconnect harness assemblies (5) and (11) . Disconnect harness assemblies (5) and (11) from the hydraulic tank. Remove temperature sensor (10) .
- Disconnect hose assemblies (7) and pipe assembly (9) from the hydraulic tank. Remove fittings (8) from the hydraulic tank.
- Remove bolts (12) and reposition filter assembly (13) .
Show/hide table
Illustration 3 | g02211635 |
- Remove cover assembly (14) and (15) .
Show/hide table
Illustration 4 | g02211636 |
- Remove bolts (16) and reposition exhaust monitor assembly (17) .
Show/hide table
Illustration 5 | g02211637 |
- Disconnect brackets (18) from the hydraulic tank.
- Disconnect harness assembly (19) . Cut cable straps (20) and reposition harness assembly (19) .
- Remove bolts (21) and plate assembly (22) .
Show/hide table
Illustration 6 | g02211638 |
- Attach Tooling (A) and a suitable lifting device to hydraulic tank (23) . The weight of hydraulic tank (23) is approximately 250 kg (550 lb).
Show/hide table
Illustration 7 | g02211639 |
Show/hide table
Illustration 8 | g02211640 |
- Disconnect hose assembly (25) and tube assembly (26) .
- Remove bolts (24) and hydraulic tank (23) .
Installation Procedure
- Install hydraulic tank (23) in the reverse order of removal.
- Apply Tooling (B) to the threads of bolts (24) . Tighten bolts (24) to a torque of 270 ± 40 N·m (200 ± 30 lb ft).
- Apply Tooling (C) to the threads of bolts (21) .
- Tighten temperature sensor (10) to a torque of 34 ± 5 N·m (25 ± 4 lb ft).
- Tighten bolts for pipe assembly (9) to a torque of 50 ± 10 N·m (37 ± 7 lb ft).
- Tighten bolts (6) to a torque of 6 ± 1 N·m (53 ± 9 lb in).
Caterpillar Information System:
Failure of the Alternator on Certain 320D, 321D CR and 323D Excavators{1405} Failure of the Alternator on Certain 320D, 321D CR and 323D Excavators{1405}
390D Excavator Hydraulic System Relief Valve (Swing)
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Wear Plates - Inspect/Replace
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Replace
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Inspect
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Check
C4.2 and C6.4 Engines for Caterpillar Built Machines Air in Fuel - Test
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Jaw - Repair
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Hub Nut - Check/Tighten
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Gear and Bearing - Lubricate
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Cutting Edge Bolts - Tighten
Caterpillar Monitoring System Service Tools
Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120} Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120}
Installation Procedure for 306-8313 Auxiliary Control Wiring Gp {1408} Installation Procedure for 306-8313 Auxiliary Control Wiring Gp {1408}
S365C and S385C Work Tools Hydraulic Cylinder
2010/09/30 A New Final Drive Group and Motor Housing is Now Used On 385C Excavators {4050}
Installation Procedure for the 338-6188 Front Lines Gp {5057} Installation Procedure for the 338-6188 Front Lines Gp {5057}
2011/01/20 New Parts are Used To Stabilize the Hydraulic Pressure on 330D Excavators and Mobile Hydraulic Power Units {5069, 5070, 5117}
390D Excavator Hydraulic System Pilot Valve (Swing Parking Brake)
390D Excavator Hydraulic System Oil Makeup (Swing System)
Installation of the 342-2952 wiring gp - front{1408, 5734} Installation of the 342-2952 wiring gp - front{1408, 5734}
A Dye Was Added to the Hydraulic Oil System on Certain Excavators{5095} A Dye Was Added to the Hydraulic Oil System on Certain Excavators{5095}
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Hydraulic Cylinder
The Muffler Bracket Assembly May Crack on Certain 345D and 345D L Excavators{1062} The Muffler Bracket Assembly May Crack on Certain 345D and 345D L Excavators{1062}