VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Caterpillar


Rotator Head Bolts - Replace

Usage:

VHS-60/4 L1P

  • Position the work tool in an upright position just above the ground.

    1. Stop the machine engine in order to prevent inadvertent movement of the work tool.

      Note: The host machine must be equipped with a boom lowering control valve in order to perform this procedure. If the host machine is not equipped with a boom lowering control valve, contact your Verachtert dealer.




      Illustration 1g02174758

    1. Remove rotator head bolt (2) from the outer ring (1) .

    1. Clean the threaded hole.

    1. Clean a new bolt (2) .

    1. Put 155-0695 Thread Lock Compound over the whole threaded length of new bolt (2).

      Table 1
      Dynamic assembly torque    
      Sales model     Bolt size     Torque value    
      VHS-60/4     M20 x 2.5    
      520 ± 70 N·m (385 ± 50 lb ft)    
      VHS-70/4     M24 x 3    
      900 ± 100 N·m (664 ± 74 lb ft)    

    1. Install the new bolt (2) and tighten the new bolt. Use appropriate tooling to apply the torque that is specified in table 1.

    1. Put a mark on rotator head bolt (2) that has been replaced.

      Note: The shear can be rotated manually in order to replace all of the bolts. Use a sufficiently long lever in order to rotate the shear.

    1. Repeat steps 3 through 8 for all of the rotator head bolts (2) on outer ring (1) .



      Illustration 2g02174775

    1. Remove bolts (5) and washers (4). Remove cover plate (3) .



      Illustration 3g02190813

    1. Cover plate (3) must be removed in order to access rotator head bolts (6) in the inner ring (7). Only a few bolts will be accessible at a time.

    1. Remove rotator head bolt (6) from the inner ring (7) .

    1. Clean the threaded hole.

    1. Clean a new bolt (6) .

    1. Put 155-0695 Thread Lock Compound over the whole threaded length of a new bolt (6) .

    1. Install the new bolt (6) and tighten new bolt. Use appropriate tooling to apply the torque that is specified in table 1.

    1. Put a mark on rotator head bolt (6) that has been replaced.

      Note: The shear can be rotated manually in order to replace all of the bolts. Use a sufficiently long lever in order to rotate the shear.

    1. Repeat steps 12 through 17 for all of the rotator head bolts (6) in the inner ring (7) .

    1. Install cover plate (3) .

    1. Install washers (4) and bolts (5) .
  • Caterpillar Information System:

    VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Inspect
    VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Check
    C4.2 and C6.4 Engines for Caterpillar Built Machines Air in Fuel - Test
    VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Jaw - Repair
    VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Hub Nut - Check/Tighten
    VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Gear and Bearing - Lubricate
    VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Cutting Edge Bolts - Tighten
    Caterpillar Monitoring System Service Tools
    The Replacement Procedure for the Hydraulic Cylinder Assembly on Certain Shears{5553} The Replacement Procedure for the Hydraulic Cylinder Assembly on Certain Shears{5553}
    VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Cutters - Inspect/Replace
    VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Bushings - Lubricate
    VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Reference Material
    VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Wear Plates - Inspect/Replace
    390D Excavator Hydraulic System Relief Valve (Swing)
    Failure of the Alternator on Certain 320D, 321D CR and 323D Excavators{1405} Failure of the Alternator on Certain 320D, 321D CR and 323D Excavators{1405}
    336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Hydraulic Tank - Remove and Install
    Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120} Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120}
    Installation Procedure for 306-8313 Auxiliary Control Wiring Gp {1408} Installation Procedure for 306-8313 Auxiliary Control Wiring Gp {1408}
    S365C and S385C Work Tools Hydraulic Cylinder
    2010/09/30 A New Final Drive Group and Motor Housing is Now Used On 385C Excavators {4050}
    Installation Procedure for the 338-6188 Front Lines Gp {5057} Installation Procedure for the 338-6188 Front Lines Gp {5057}
    2011/01/20 New Parts are Used To Stabilize the Hydraulic Pressure on 330D Excavators and Mobile Hydraulic Power Units {5069, 5070, 5117}
    390D Excavator Hydraulic System Pilot Valve (Swing Parking Brake)
    390D Excavator Hydraulic System Oil Makeup (Swing System)
    Back to top
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.