Bushings - Lubricate
Show/hide table
 | |
| Illustration 1 | g02170193 |
- Close the jaw of the shear.
- Place the shear on the ground.
- Turn off the engine of the host machine. Release the hydraulic pressure in the hydraulic system. Refer to the "Service Manual" of the host machine for the proper procedure to release the hydraulic pressure.
- Clean the fittings with a clean rag before you lubricate the fittings in order to prevent contamination.
- Lubricate the seven grease fittings. There are two fittings on the pivot pin for the cylinder (1). There is one fitting on the end of the cylinder (2). There are two fittings on the pin for the cutting jaw (3). There are two fittings on the bushing for the hub (4) .
Refer to Operation and Maintenance Manual, "General Maintenance Information" for lubrication information.
Caterpillar Information System:
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Reference Material
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Lifting and Tying Down
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Transport Position
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600} NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Operation
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Daily Inspection
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Work Tool Installation and Removal
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Declaration of Conformity
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Plate Locations and Film Locations
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Approved Machines
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Specifications
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Safety Messages
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Cutters - Inspect/Replace
The Replacement Procedure for the Hydraulic Cylinder Assembly on Certain Shears{5553} The Replacement Procedure for the Hydraulic Cylinder Assembly on Certain Shears{5553}
Caterpillar Monitoring System Service Tools
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Cutting Edge Bolts - Tighten
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Gear and Bearing - Lubricate
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Hub Nut - Check/Tighten
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Jaw - Repair
C4.2 and C6.4 Engines for Caterpillar Built Machines Air in Fuel - Test
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Check
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Inspect
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Rotator Head Bolts - Replace
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Wear Plates - Inspect/Replace