Engine Oil Pump - Assemble
组装步骤
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 组装前，确保机油泵的所有零件清洁。
注: 利用干净的机油润滑机油泵的所有内构件。
- 将驱动齿轮 (7) 压到轴组件上，直到驱动齿轮 (7) 与轴组件端部齐平为止。
Show/hide table
 | |
| 图 1 | g01026667 |
- 将轴 (6) 安装到机油泵壳体组件 (8) 内。 将轴承安装到惰轮 (5) 中。 安装轴承，使惰轮 (5) 的轮毂螺栓面和轴承间的距离为 0.75 ± 0.25 mm (0.030 ± 0.010 in)。
- 将惰轮 (5) 安装到轴 (6) 上。 安装垫圈 (4) 和螺栓 (3) 。 拧紧螺栓 (3) ，使其扭矩达到 70 ± 15 N·m (52 ± 11 lb ft)。
- 检查机油吸油管 (2) 内所用密封垫的状态。 如果垫片损坏，则更换垫片。 安装密封垫和机油吸油管 (2) 。
Show/hide table
 | |
| 图 2 | g01026664 |
- 检查出口弯头 (1) 内所用 O 形密封圈的状态。 更换损坏的 O 形密封圈。 安装 O 形密封圈和出口弯头 (1) 。
End By: 安装发动机机油泵。 请参阅 拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
G3406 Engine Alarms and Shutoffs
3126B Engines for Caterpillar Built Machines Engine Oil Pump - Remove
3176C and 3196 Engines for Caterpillar Built Machines Throttle Position Sensor
3408E and 3412E Engines for Caterpillar Built Machines Turbocharger Outlet Pressure Sensor
3500B Engines for Caterpillar Built Power Modules with the ADEM 2 Electronic Control Module Diagnostic Codes
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0100 - FMI 02 (for MUI and PEEC Engines)
2000/05/08 Improved Caterpillar O-ring Face Seals are Now Available {7555}
C-12, C-15 and C-16 Engines for Caterpillar Built Machines CID 0342 FMI 11 Secondary Engine Speed Sensor mechanical failure
C-10, C-12, C-15 and C-16 Industrial Engines CID 0320 FMI 11 Speed/Timing Sensor mechanical failure
Alternator - Delco 21SI Alternator - Disassemble
G3516B Engines MID 036 - CID 0443 - FMI 03 Crank Terminate Relay short to +batt
3500B Engines for Caterpillar Built Power Modules with the ADEM 2 Electronic Control Module Engine Speed/Timing Sensor - Calibrate
3126B Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
3126B Engines for Caterpillar Built Machines Flywheel - Remove and Install
3126B Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
3126B Engines for Caterpillar Built Machines Housing (Front) - Install
EMCPII+ for Gas Engines GSC CID 0100 - FMI 03
3176C and 3196 Engines for Caterpillar Built Machines Fuel Dilution of Engine Oil
3126B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
2000/05/01 Service Manual Module, RENR2484, "Electronic Modular Control Panel II+ (EMCP II+)" is Now Available {4490}
Alternator - Delco 21SI Alternator - Assemble
325, 325B and 325L Excavators Hydraulic System Pressure - Release
3176C and 3196 Engines For Caterpillar Built Machines Fuel Filter Base - Remove
2000/05/01 Corrections To Disassembly and Assembly Modules, G3600 Engines , "Pistons and Connecting Rods - Install" {1225}