Axle - Install - Rear Axle
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1U-9744 | Hydraulic Jack | 1 |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Use a suitable lifting device to position transmission (3), as shown. The weight of transmission (3) is approximately
136 kg (300 lb) . - Install bolts (8). Tighten bolts (8) to a torque of
79 N·m (58 lb ft) .Show/hide tableIllustration 2 g01175096 Show/hide tableIllustration 3 g01175097 - Use Tooling (A) and a suitable lifting device to position rear axle (5) and transmission (3) under the machine. The weight of rear axle (5) and transmission (3) is approximately
794 kg (1750 lb) . - Install nuts (6) and connect hose assembly (7).
Show/hide table
Illustration 4 g01175093 - Connect harness assembly (2).
Show/hide table
Illustration 5 g01175091 - Connect hose assemblies (1).
- Fill the rear axle with clean oil. Refer to Operation and Maintenance Manual, "Axle Oil (Rear) - Change".
Show/hide table
Illustration 1 | g01175098 |
End By:
- Install the rear tires and rims. Refer to Disassembly and Assembly, "Tire and Rim - Install".
- Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Caterpillar Information System:
M318C and M322C Wheeled Excavators Power Train Axle - Remove - Rear Axle
325D Material Handler Storage Box
345C MHPU Mobile Hydraulic Power Unit Shipping the Machine - Shipping Specifications
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Fuel Tank - Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Fuel Tank - Remove
325D and 329D Excavators Quick Coupler Operation - Double Action (If Equipped)
323D Excavator Capacities (Refill)
302.5C Mini Hydraulic Excavator Engine Supplement Fan - Remove and Install
323D Excavator Hydraulic System Oil - Change
302.5C Mini Hydraulic Excavator Engine Supplement Alternator - Remove and Install
M318C and M322C Excavators Machine Systems Stabilizer - Remove and Install
345C UHD Excavator and 345C Mobile Hydraulic Power Unit Demolition Boom Installation
Troubleshooting Instructions for the 157-3210 Control Panel {1408, 7320} Troubleshooting Instructions for the 157-3210 Control Panel {1408, 7320}
323D Excavator Equipment Lowering with Engine Stopped
345C Excavators Joystick Controls
Hydraulic Cylinder Repair Process {7562} Hydraulic Cylinder Repair Process {7562}
303C CR, 303.5C CR, 304C CR and 305C CR Mini Hydraulic Excavators Quick Coupler Operation - Manual Pin Grabber Quick Coupler (If Equipped)
568 GF and 568 LL Forest Machine Leaving the Machine
301.6C and 301.8C Mini Hydraulic Excavators Engine Supplement Electric Starting Motor - Remove and Install
301.6C, 301.8C and 302.5C Mini Hydraulic Excavators Capacities (Refill)
301.6C and 301.8C Mini Hydraulic Excavators Engine Supplement Fuel Transfer Pump - Remove and Install
302.5C Mini Hydraulic Excavator Engine Supplement Electric Starting Motor - Remove and Install
C15 and C18 Petroleum Generator Sets Electrical System
BR160, BR166, BR172, BR272 and BR378 Brush Cutters Hydraulic System