Swing Gear and Bearing
Show/hide table
图 1 | g01808514 |
顶视图 |
Show/hide table
图 2 | g01808515 |
注: 相对于底座组件和轴承止动块 (2) 定位内座圈 (3) 上的 "S" 。 有关正确的方向,请参看图 1。
(4) 将 1U-8846 密封垫密封胶 涂敷在齿轮总成和上部机架组件的配合面之间。 将 1U-8846 密封垫密封胶 涂敷在齿轮总成和底座组件的配合面之间。
(5) 按照以下步骤拧紧 60 条螺栓:
- 将 154-9731 防咬合剂 涂在螺栓的螺纹上。 螺栓座无需涂抹。
- 以 400 ± 50 N·m (300 ± 37 lb ft) 的扭矩拧紧螺栓。
- 转动 60 ± 5 度,再次拧紧螺栓。
注: 将 4C-4030 螺纹锁固胶 涂覆在螺栓 (6) 的螺纹上。
(6) 四只螺栓的扭矩 ... 20 ± 2 N·m (15 ± 1 lb ft)
注: 将 4C-4030 螺纹锁固胶 涂抹在螺栓 (7) 螺纹上。
(7) 18 只螺栓的扭矩 ... 37 ± 4 N·m (27 ± 3 lb ft)
(8) 在定位销孔的螺纹上涂抹 154-9731 螺纹锁固胶 。
(9) 按照以下步骤拧紧 37 条螺栓:
- 在螺栓螺纹上涂抹 4C-5599 防咬合剂 。 螺栓座和垫圈表面无需涂抹。
- 将螺栓上紧到 700 ± 50 N·m (520 ± 37 lb ft)。
- 转动 60 ± 5 度,再次拧紧螺栓。
Caterpillar Information System:
318C and 319C Excavators Hydraulic System Displacement Change Valve
3306C Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
Logging Forks Log Fork - Lubricate
Logging Forks Daily Inspection
Logging Forks Lifting and Tying Down
Logging Forks Transport Position
Logging Forks Work Tool Installation and Removal
Logging Forks Plate Locations and Film Locations
Logging Forks Approved Machines
M313C and M315C Excavators Engine Oil and Filter - Change
M313C and M315C Excavators Engine Oil Sample - Obtain
CV16B and CV18B Vibratory Compactors Frame (Rear) - Remove and Install
Logging Forks Safety Messages
Logging Forks Reference Material
3306C Engines for Caterpillar Built Machines Fuel Injection Nozzle - Test
M316C, M318C and M322C Excavators and M318C MH and M322C MH Material Handlers Joystick Steering - If Equipped
Logging Forks Rated Load
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Tilt Cylinder
318C and 319C Excavators Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
3306C Engines for Caterpillar Built Machines Gear Group (Front) - Time
318C and 319C Excavators Hydraulic System Main Hydraulic System
2004/10/04 A New Mounting Gasket for the Fuel Transfer Pump is Available {1256}
365C Excavator Hydraulic System Electronic Control System
365C Excavator, 365C Material Handler and 365C Front Shovel Machine System Specifications Return and Oil Filter Lines