Housing (Front) - Install
安装步骤
Show/hide table
需要的工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-8440     | 合成洗涤剂     | 1     |
B     | 4C-9500     | 快速粘合底胶     | 1     |
C     | 1U-8846     | 密封垫密封胶     | 1     |
- 使用工具 (A) ,清洁前壳体 (4) 接合面。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g01151892 |
- 在接合面上涂抹工具 (B) 。
- 在接合面上涂抹工具 (C) 。 均匀地铺开密封胶。 必须在涂抹密封胶后十分钟以内安装前壳体 (4) 。
注: 不要让工具 (C) 密封住前壳体 (4) 上的主机油道。
- 在缸体上定位前壳体 (4) 。
- 安装螺栓 (3) 。
- 安装螺栓 (5) 。
- 连接线束组件 (1) 和 (2) 。
Show/hide table
图 2 | g01151885 |
End By:
- 安装凸轮轴。 请参阅 解体和组装, "凸轮轴 - 安装"。
- 安装曲轴前油封。 请参阅 解体和组装, "曲轴前油封 - 安装"。
- 安装单体喷油器液压泵。 请参阅 解体和组装, "单体喷油器液压泵 - 安装"。
Caterpillar Information System:
3056 Engine for Caterpillar Built Machines Engine Oil Pump - Install
C9 Engines for Caterpillar Built Machines Housing (Front) - Remove
3056 Engine for Caterpillar Built Machines Engine Oil Pump - Remove
C9 Engine For Caterpillar Built Machines Engine Oil Pan - Remove and Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Intermittent Engine Shutdown
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Starting with Jump Start Cables
SR4 and SR4B Generators and Control Panels Tools
3612 and 3616 Engines Idler Gears (Rear) - Install
C9 Engine For Caterpillar Built Machines Crankshaft Front Seal - Install
C9 Engine For Caterpillar Built Machines Crankshaft Front Seal - Remove
Caterpillar Monitoring System for Electronic Modular Control Panel Initial Troubleshooting Procedure
C9 Engine For Caterpillar Built Machines Front Cover - Install
C9 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3500B and 3500B High Displacement Generator Set Engines Intermittent Low Power or Power Cutout
3500B and 3500B High Displacement Generator Set Engines Low Power/Poor or No Response to Throttle
3176C and 3196 Engines For Caterpillar Built Machines Belt Tensioner - Remove and Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Intermittent Low Power or Power Cutout
3512B Marine Auxiliary Engines Vibration Damper - Remove and Install
3500B and 3500B High Displacement Generator Set Engines Engine Cranks but Will Not Start
C9 Engine For Caterpillar Built Machines Crankshaft Main Bearings - Install
3512B Marine Auxiliary Engines Vibration Sensor - Remove and Install
3612 and 3616 Engines Idler Gears (Front) - Install
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Remove
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Install