Idler Gears (Front) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
B     | 1P-0510     | 冲头总成     | 1     |
C     | 8T-5096     | 千分表     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将止推垫圈 (5) 在前壳体的定位销上放好。 新止推垫圈的厚度为9.45 ± 0.05 mm (0.372 ± 0.002 in)。
Show/hide table
图 1 | g00561407 |
- 如果拆下了轴承 (4) ,用工具 (B) 将轴承安装到惰轮 (1) 上。 安装轴承,直至尺寸 (X) 为2.50 ± 0.50 mm (0.098 ± 0.020 in)。 安装后轴承内径应为 69.950 ± 0.010 mm (2.7539 ± 0.0004 in)。
Show/hide table
图 2 | g01296368 |
注: 图中的惰轮轴承表示为内部供油的凹槽。 新的惰轮轴承不带内部供油的凹槽。
- 将 O 形密封圈 (3) 安装惰轮轴 (2) 上。 在 O 形密封圈上涂抹清洁的发动机机油。
Show/hide table
图 3 | g00561404 |
- 将干净的发动机油涂抹在惰齿轮 (1) 的轴承上。
Show/hide table
图 4 | g00561379 |
注: 每侧的惰齿轮都不同。 必须将惰齿轮安装在正确一侧,以与曲轴齿轮正确接合。 左侧惰齿轮有67个齿,右侧惰齿轮有68个齿。
- 将惰齿轮 (1) 以及前部惰齿轮的大肩部放好。 安装惰轮轴 (2) 。
- 右侧惰轮轴应在惰轮轴二点钟位置带有机油孔 (A) 。
Show/hide table注意 应定位前齿轮组中使用的惰轮轴,以使惰齿轮轴承得到正确润滑。 惰齿轮包含一个中央承压供油孔。 惰轮轴中的横向钻孔将承压机油供应至惰齿轮轴承。
注: 对于"标准转向"发动机,使用以下图示。
Show/hide table图 5 g01296492
(A) 右侧惰轮轴上的交叉钻机油孔
(B) 左侧惰轮轴上的交叉钻机油孔
- 左侧惰轮轴应在惰轮轴五点钟位置带有机油孔 (B) 。
- 右侧惰轮轴应在惰轮轴八点钟位置带有机油孔 (C) 。
注: 对于"反向转向"发动机,使用以下图示。
Show/hide table图 6 g01296495
(C) 右侧惰轮轴上的交叉钻机油孔
(D) 左侧惰轮轴上的交叉钻机油孔
- 左侧惰轮轴应在惰轮轴十一点钟位置带有机油孔 (D) 。
- 安装将惰轮轴固定入位的螺栓。
- 使用工具 (C) 检查曲轴齿轮与惰轮之间的齿隙。 齿隙应为 0.051至 0.533 mm (0.0020 至 0.0209 in)。
- 使用工具 (C) 检查惰轮的轴向间隙。 轴向间隙应为 0.25 至 0.85 mm (0.010 至 0.033 in)。
End By:
- 安装发动机机油泵。 请参阅 拆解和组装, "发动机机油泵 - 安装"。
- 安装水泵。 请参考 拆解和组装, "水泵 - 安装"和 拆解和组装, "辅助水泵 - 安装"。
Caterpillar Information System:
3512B Marine Auxiliary Engines Vibration Sensor - Remove and Install
C9 Engine For Caterpillar Built Machines Crankshaft Main Bearings - Install
3500B and 3500B High Displacement Generator Set Engines Engine Cranks but Will Not Start
3512B Marine Auxiliary Engines Vibration Damper - Remove and Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Intermittent Low Power or Power Cutout
3176C and 3196 Engines For Caterpillar Built Machines Belt Tensioner - Remove and Install
3500B and 3500B High Displacement Generator Set Engines Low Power/Poor or No Response to Throttle
3500B and 3500B High Displacement Generator Set Engines Intermittent Low Power or Power Cutout
C9 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
C9 Engine For Caterpillar Built Machines Housing (Front) - Install
3056 Engine for Caterpillar Built Machines Engine Oil Pump - Install
C9 Engines for Caterpillar Built Machines Housing (Front) - Remove
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Remove
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Install
3176C and 3196 Engines For Caterpillar Built Machines Camshaft - Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Excessive Black Smoke
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Bearings - Install
3176C and 3196 Industrial Engines Camshaft Bearings - Remove
3612 and 3616 Engines Housing (Front) - Remove
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Excessive White Smoke
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 590 FMI 9 Engine Electronic Control Module Abnormal Update - Test
3512B Marine Auxiliary Engines Front Drive Housing - Remove and Install
3612 and 3616 Engines Housing (Front) - Install
3612 and 3616 Engines Housing (Rear) - Remove