Camshaft - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 131-1525 | 凸轮轴导向器 | 1 |
- 安装工具 (A)。
注: 确保凸轮轴 (2) 和工具 (A) 是清洁的。 将清洁的发动机机油涂抹到凸轮轴 (2) 的凸轮和轴颈和工具 (A)。
注: 安装凸轮轴 (2) 时,从两个方向旋转凸轮轴来防止凸轮轴轴承孔卡住。
- 小心地将凸轮轴 (2) 安装到发动机中。
Show/hide table
注意 安装凸轮轴时,确保 1 号缸位于压缩行程的上止点,并且正时螺栓安装在飞轮里。 凸轮轴正时是非常重要的。 凸轮轴驱动齿轮上的正时标记必须对准惰轮上的正时标记。 更多信息,请参考技术规格手册。
- 确保惰轮上的正时标识 (3) 对准曲轴齿轮上的正时标识和凸轮轴驱动齿轮。
- 安装止推销 (1) 。 将止推销 (1) 上紧到
28 ± 7 N·m (20 ± 5 lb ft) 的扭矩。 拆卸用来固定气门挺杆的电线。
Show/hide table
图 1 | g00813405 |
Show/hide table
图 2 | g00813917 |
结束:
- 安装凸轮轴位置传感器。 请参阅拆解和组装, "凸轮轴位置传感器 - 拆卸和安装"。
- 安装前盖。 请参阅拆解和组装, "前盖 - 安装"。
- 安装摇臂轴组件和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 安装"。
Caterpillar Information System:
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Install
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Remove
3612 and 3616 Engines Idler Gears (Front) - Install
3512B Marine Auxiliary Engines Vibration Sensor - Remove and Install
C9 Engine For Caterpillar Built Machines Crankshaft Main Bearings - Install
3500B and 3500B High Displacement Generator Set Engines Engine Cranks but Will Not Start
3512B Marine Auxiliary Engines Vibration Damper - Remove and Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Intermittent Low Power or Power Cutout
3176C and 3196 Engines For Caterpillar Built Machines Belt Tensioner - Remove and Install
3500B and 3500B High Displacement Generator Set Engines Low Power/Poor or No Response to Throttle
3500B and 3500B High Displacement Generator Set Engines Intermittent Low Power or Power Cutout
C9 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Excessive Black Smoke
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Bearings - Install
3176C and 3196 Industrial Engines Camshaft Bearings - Remove
3612 and 3616 Engines Housing (Front) - Remove
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Excessive White Smoke
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 590 FMI 9 Engine Electronic Control Module Abnormal Update - Test
3512B Marine Auxiliary Engines Front Drive Housing - Remove and Install
3612 and 3616 Engines Housing (Front) - Install
3612 and 3616 Engines Housing (Rear) - Remove
3056 Engine for Caterpillar Built Machines Engine Lifting Bracket - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Data Link
3612 and 3616 Engines Housing (Rear) - Install