Vibration Damper - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (1) in order to remove damper guard (2).
Show/hide table
Illustration 2 g00642323 Typical example - Install Tool (A) onto damper (3). Attach a suitable lifting device to Tool (A). The weight of the damper is approximately
79 kg (175 lb) . - Remove two bolts (4). Install two 1-14 NF guide bolts. Remove the rest of bolts (4). Note the position of alignment marks (5) and (6) on the end of the crankshaft and on the damper. Remove the damper.
Show/hide table
Illustration 1 | g00637192 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Before you install the damper, inspect the condition of the damper. Repair the damper or replace the damper for any of the following conditions:
- The damper is dented, cracked, or leaking.
- The paint on the damper is discolored from heat.
- The engine has had a failure because of a broken crankshaft.
- An analysis of the oil has revealed that the front bearing of the crankshaft is badly worn.
- There is a large amount of gear train wear that is not caused by a lack of oil.
- Install two 1-14 NF guide bolts in the end of the crankshaft.
- Install Tool (A) onto damper (3). Attach a suitable lifting device to Tool (A). The weight of the damper is approximately
79 kg (175 lb) . - Lift damper (3) into position according to alignment marks (5) and (6) on the end of the crankshaft and on the damper.
- Coat bolts (4) with 2P-2506 Thread Compound. Install bolts (4) in order to hold the damper in position. Remove the two guide bolts from the end of the crankshaft. Install the rest of bolts (4). Tighten bolts (4) to a torque of
1125 ± 100 N·m (830 ± 75 lb ft) .Show/hide tableIllustration 4 g00637192 - Attach damper guard (2) with bolts (1). Tighten the bolts to a torque of
15 ± 3 N·m (133 ± 27 lb in) .
Show/hide table
Illustration 3 | g00642323 |
Typical example |
Caterpillar Information System:
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Intermittent Low Power or Power Cutout
3176C and 3196 Engines For Caterpillar Built Machines Belt Tensioner - Remove and Install
3500B and 3500B High Displacement Generator Set Engines Low Power/Poor or No Response to Throttle
3500B and 3500B High Displacement Generator Set Engines Intermittent Low Power or Power Cutout
C9 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
C9 Engine For Caterpillar Built Machines Housing (Front) - Install
3056 Engine for Caterpillar Built Machines Engine Oil Pump - Install
C9 Engines for Caterpillar Built Machines Housing (Front) - Remove
3056 Engine for Caterpillar Built Machines Engine Oil Pump - Remove
C9 Engine For Caterpillar Built Machines Engine Oil Pan - Remove and Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Intermittent Engine Shutdown
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Starting with Jump Start Cables
3500B and 3500B High Displacement Generator Set Engines Engine Cranks but Will Not Start
C9 Engine For Caterpillar Built Machines Crankshaft Main Bearings - Install
3512B Marine Auxiliary Engines Vibration Sensor - Remove and Install
3612 and 3616 Engines Idler Gears (Front) - Install
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Remove
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Install
3176C and 3196 Engines For Caterpillar Built Machines Camshaft - Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Excessive Black Smoke
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Bearings - Install
3176C and 3196 Industrial Engines Camshaft Bearings - Remove
3612 and 3616 Engines Housing (Front) - Remove
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Excessive White Smoke