Rear Power Take-Off (RPTO) - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 8T-0514     | 导向螺栓     | 2     |
B     | 1P-0520     | 冲头总成     | 1     |
C     | 1P-0510     | 冲头总成     | 1     |
开始:
- 拆下飞轮。 请参阅拆解和组装, "飞轮 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (A) 安装在曲轴中。
Show/hide table
图 1 | g00520761 |
- 拆下螺栓 (1) 和曲轴密封件 (2) 。
- 拆下螺栓 (3) 、盖 (4) 和密封垫。 检验密封垫的状况。 必要时,更换密封垫。
- 从曲轴上拆下曲轴齿轮 (5) 。 从曲轴齿轮 (5) 上拆下 O 形密封圈。
Show/hide table
图 2 | g01061868 |
- 拆下工具 (A) 。
- 拆下将轴 (7) 固定至飞轮壳的螺栓 (6) 。
- 使用撬杆拆下轴 (7) 和齿轮组件 (8) 。
Show/hide table
图 3 | g00520763 |
- 检查齿轮组件中的轴承状况。 如有必要,使用工具 (B) 和适当的压力机从齿轮上拆卸轴承 (9) 。
Show/hide table
图 4 | g00520764 |
- 拆下将托架组件 (11) 固定至飞轮壳的螺栓 (10) 。 在位置 (12) 安装两个彼此相对的螺栓 (10) 。 将这两个螺栓用作顶出螺钉以拆卸托架组件 (11) 。
Show/hide table
图 5 | g00520766 |
- 从托架组件 (11) 上拆下 O 形密封圈 (15) 和唇型密封 (13) 。
Show/hide table
图 6 | g00765120 |
- 检查轴承 (14) 的状况。 如有必要,使用工具 (C) 和适当的压力机从托架组件 (11) 上拆卸轴承 (14) 。
- 拆卸螺栓 (16) 、盖组件 (17) 和止推垫圈 (18) 。 更换O 形密封圈。
Show/hide table
图 7 | g00520769 |
Show/hide table
图 8 | g00520770 |
- 检查止推垫圈 (18) 的状况。 如有必要,更换止推垫圈 (18) 。
注: 止推垫圈 (18) 的最小允许厚度为 4.665 mm (0.1837 in)。
- 检查盖组件 (17) 中止推垫圈 (18) 的定位销的状况。 如果需要更换,拆卸定位销。
- 从输出轴拆卸螺栓 (19) 和止推片 (20) 。
Show/hide table
图 9 | g00520771 |
- 拆卸将齿轮 (23) 固定至输出轴 (22) 的内六角头螺栓 (21) 。
Show/hide table
图 10 | g01061870 |
- 从齿轮 (23) 上拆下输出轴 (22) 。 将齿轮 (23) 从飞轮壳上拆下。
- 将止推垫圈 (24) 从飞轮壳上拆下。
Show/hide table
图 11 | g00520774 |
- 检查止推垫圈 (24) 的状况。 如有必要,更换止推垫圈 (24) 。
注: 止推垫圈 (24) 的最小允许厚度为 4.665 mm (0.1837 in)。
- 检查飞轮壳中止推垫圈 (24) 的定位销的状况。 如果需要更换,拆卸定位销。
- 检查轴承 (25) 的状况。 如有必要,使用工具 (C) 从飞轮壳拆卸轴承 (25) 。
Caterpillar Information System:
3612 and 3616 Engines Idler Gears (Front) - Install
3512B Marine Auxiliary Engines Vibration Sensor - Remove and Install
C9 Engine For Caterpillar Built Machines Crankshaft Main Bearings - Install
3500B and 3500B High Displacement Generator Set Engines Engine Cranks but Will Not Start
3512B Marine Auxiliary Engines Vibration Damper - Remove and Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Intermittent Low Power or Power Cutout
3176C and 3196 Engines For Caterpillar Built Machines Belt Tensioner - Remove and Install
3500B and 3500B High Displacement Generator Set Engines Low Power/Poor or No Response to Throttle
3500B and 3500B High Displacement Generator Set Engines Intermittent Low Power or Power Cutout
C9 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
C9 Engine For Caterpillar Built Machines Housing (Front) - Install
3056 Engine for Caterpillar Built Machines Engine Oil Pump - Install
3176C and 3196 Industrial Engines Rear Power Take-Off (RPTO) - Install
3176C and 3196 Engines For Caterpillar Built Machines Camshaft - Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Excessive Black Smoke
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Bearings - Install
3176C and 3196 Industrial Engines Camshaft Bearings - Remove
3612 and 3616 Engines Housing (Front) - Remove
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Excessive White Smoke
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 590 FMI 9 Engine Electronic Control Module Abnormal Update - Test
3512B Marine Auxiliary Engines Front Drive Housing - Remove and Install
3612 and 3616 Engines Housing (Front) - Install
3612 and 3616 Engines Housing (Rear) - Remove
3056 Engine for Caterpillar Built Machines Engine Lifting Bracket - Remove and Install