Camshaft Bearings - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A.     | 8S-2241     | 凸轮轴轴承工具总成     | 1     |
开始:
- 拆下凸轮轴。 请参阅拆解和组装, "凸轮轴 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 拆下凸轮轴轴承 (1) 。
Show/hide table
图 1 | g01138826 |
注: 为了便于组装,拆卸之前记录各个凸轮轴轴承中机油孔的方位。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A.     | 8S-2241     | 凸轮轴轴承工具总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 请参阅图 2 以了解轴承位置。
(1a) 轴承 (1a) 的安装尺寸 (A) ... 816.5 ± 0.8 mm (32.15 ± 0.03 in)
(1b) 轴承 (1b) 的安装尺寸 (B) ... 536.5 ± 0.8 mm (21.12 ± 0.03 in)
(1c) 轴承 (1c) 的安装尺寸 (C) ... 294.5 ± 0.8 mm (11.59 ± 0.03 in)
(1d) 轴承 (1d) 的安装尺寸 (D) ... 0.50 ± 0.25 mm (0.020 ± 0.010 in)
Show/hide table
图 2 | g02715711 |
- 使用工具 (A) ,安装除前轴承外的所有凸轮轴轴承 (1) 。 在各个轴承中找到机油孔 (2) ,使机油孔 (2) 位于孔的顶部。 将接头 (3) 置于正确位置。
Show/hide table
图 3 | g01138826 |
Show/hide table
图 4 | g01138827 |
Show/hide table
图 5 | g01138828 |
- 使用工具 (A) 安装凸轮轴前轴承。 将凸轮轴前轴承中的机油孔 (2) 与缸体中的机油孔对准。 将凸轮轴前轴承中的接头 (3) 置于正确位置(朝向缸体)。 请参阅技术规格, "缸体"以了解更多信息。
End By: 安装凸轮轴。 请参阅 拆解和组装, "凸轮轴 - 安装"。
Caterpillar Information System:
C9 Engine For Caterpillar Built Machines Camshaft Gear - Remove and Install
SR500 Generators Insulation - Test
C-9 Engines for Caterpillar Built Machines Front Housing and Covers
3612 and 3616 Engines Engine Oil Pan - Assemble
3406E Truck Engine Inlet Air Temperature Sensor
Caterpillar 270 Air Compressor General Testing and Adjusting Information
Bendix DuraFlo 596 Air Compressor Air Compressor Fails to Unload
3618 Engine Crankshaft Front Seal and Wear Sleeve - Install
3612 and 3616 Engines Engine Oil Pan - Disassemble
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Schematics and Wiring Diagrams
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (Generator Set) - Flash Program
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Connector Contact Identification of Generator Set Control
Bendix DuraFlo 596 Air Compressor Excessive Oil at Exhaust Ports or Air Strainer
584 and 584HD Forwarders Emissions Certification Film
Electronic Modular Control Panel II (EMCP II) Component Location
3612 and 3616 Engines Oil Temperature Regulators - Remove and Install
C9 Engine For Caterpillar Built Machines Pistons and Connecting Rods - Remove
SR500 Generators Parallel Operation
SR4 and SR4B Generators and Control Panels Bearing - Lubricate
3126B and 3126E On-highway Engines System Configuration Parameters
SR4 and SR4B Generators and Control Panels Electromechanical Control Panel for Switchgear Conversion
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Install
C-10 and C-12 Engines Engine Oil Pan - Remove and Install
3612 and 3616 Engines Accessory Drive - Remove