Oil Temperature Regulators - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 将来自油温调节器壳体的发动机油排放到一个合适的容器,以便存放或弃置。 请参阅操作和保养手册, "发动机机油 - 更换"。
- 如果安装了燃油表传感器,将其从 (4) 护盖上断开。
Show/hide table
图 1 | g00554514 |
典型示例 |
- 拆下将护盖 (2) 固定到油温调节器壳体 (1) 上的螺栓。
- 拆下盖 (2) 和管 (3) 。
- 将密封垫和油温调节器 (5) 从油温调节器壳体 (1) 上拆下。
Show/hide table
图 2 | g00554516 |
注: 要拆下油温调节器 (5) ,不必将油温调节器壳体 (1) 从发动机上拆下。
- 将唇形密封件从油温调节器壳体 (1) 上拆下。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 221-8647     | 密封安装工具总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在密封唇远离护盖 (2) 的情况下,使用工具 (A) 将唇形密封件安装到油温调节器壳体 (1) 中。
Show/hide table
图 3 | g00554516 |
Show/hide table
图 4 | g00554514 |
- 将油温调节器 (5) 安装在油温调节器壳体 (1) 中。
- 将新 O 型密封圈安装在管 (3) 上。 在 O 形密封圈上涂抹清洁的发动机机油。
- 将管路 (3) 、护盖 (2) 以及密封垫在油温调节器壳体 (1) 上放好。 安装将管路 (3) 、护盖 (2) 和密封垫固定入位的螺栓。
- 将燃油表传感器 (4) 连接到护盖。
- 向发动机加注机油到正确的油位。 请参阅操作和保养手册, "发动机机油 - 更换"。
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) Component Location
584 and 584HD Forwarders Emissions Certification Film
Bendix DuraFlo 596 Air Compressor Excessive Oil at Exhaust Ports or Air Strainer
C9.3 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
C9 Engine For Caterpillar Built Machines Camshaft Gear - Remove and Install
SR500 Generators Insulation - Test
C-9 Engines for Caterpillar Built Machines Front Housing and Covers
3612 and 3616 Engines Engine Oil Pan - Assemble
3406E Truck Engine Inlet Air Temperature Sensor
Caterpillar 270 Air Compressor General Testing and Adjusting Information
Bendix DuraFlo 596 Air Compressor Air Compressor Fails to Unload
3618 Engine Crankshaft Front Seal and Wear Sleeve - Install
C9 Engine For Caterpillar Built Machines Pistons and Connecting Rods - Remove
SR500 Generators Parallel Operation
SR4 and SR4B Generators and Control Panels Bearing - Lubricate
3126B and 3126E On-highway Engines System Configuration Parameters
SR4 and SR4B Generators and Control Panels Electromechanical Control Panel for Switchgear Conversion
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Install
C-10 and C-12 Engines Engine Oil Pan - Remove and Install
3612 and 3616 Engines Accessory Drive - Remove
3612 and 3616 Engines Accessory Drive - Install
C15 and C18 Petroleum Generator Sets Cold Start Strategy
3126B Marine Engine Cold Weather Starting
Bendix DuraFlo 596 Air Compressor Air Compressor is Noisy