Crankshaft Rear Seal - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 9U-6205 | Rear Seal Installer | 1 |
1P-0510 | Driver Group | 1 | |
B | FT-2806 | Alignment Tool | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Engines with 14 Bolt Housing Assembly
- Inspect the condition of the gasket. Replace the gasket, if necessary.
- Clean the areas of the parts that will contact each other.
Show/hide table
Illustration 1 g00804647 - Use Tooling (A) and a suitable press to install the crankshaft rear seal into the housing.
- Lubricate the components with clean engine oil. Install Tooling (A) onto the crankshaft flange.
- Position the new gasket on the dowels in the cylinder block.
Show/hide table
Illustration 2 g00606404 Typical example - Place housing (3) and crankshaft rear seal (4) over Tooling (A).
- Position housing (3) on the dowels in the cylinder block.
- Remove Tooling (A).
Show/hide table
Illustration 3 g00632744 The flywheel housing has been removed for photographic purposes only. - Install socket head bolts (2) onto housing (3).
- Install bolts (1) in order to fasten housing (3) to the cylinder block. Tighten all of the bolts to a torque of
22 N·m (16 lb ft) .
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the plastic sleeve after the housing assembly is installed.
- Place Tooling (B) over housing assembly (3). This will center the housing assembly onto the crankshaft flange.
Show/hide table
Illustration 5 g00830867 - Install the bolts with Tooling (B) in position in order to fasten housing assembly (3) to the cylinder block. Tighten bolts 1 and 2 to a torque of
22 N·m (16 lb ft) . - Remove Tooling (B). Tighten the remaining bolts in sequence to a torque of
22 N·m (16 lb ft) .
Show/hide table
Illustration 4 | g00831176 |
Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the crankshaft flange before installation.
End By:
- Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar Information System:
3612 and 3616 Engines Engine Oil Pan - Install
Bendix DuraFlo 596 Air Compressor Air Compressor Maintenance Procedures
3126B Truck Engine Reference Material
3126B Truck Engine Maintenance Interval Schedule
3126B Truck Engine Refill Capacities
3126B Truck Engine Engine Operation
C-9 Engines for Caterpillar Built Machines Unit Injector
3054 and 3056 Industrial and Generator Set Engines Fan Drive
3612 and 3616 Engines Engine Oil Pan - Remove
3618 Engine Crankshaft Rear Gear - Remove and Install
C9 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Service Record
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Connector Contact Identification of Generator Set Control
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (Generator Set) - Flash Program
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Schematics and Wiring Diagrams
3612 and 3616 Engines Engine Oil Pan - Disassemble
3618 Engine Crankshaft Front Seal and Wear Sleeve - Install
Bendix DuraFlo 596 Air Compressor Air Compressor Fails to Unload
Caterpillar 270 Air Compressor General Testing and Adjusting Information
3406E Truck Engine Inlet Air Temperature Sensor
3612 and 3616 Engines Engine Oil Pan - Assemble
C-9 Engines for Caterpillar Built Machines Front Housing and Covers
SR500 Generators Insulation - Test
C9 Engine For Caterpillar Built Machines Camshaft Gear - Remove and Install