Engine Oil Pan - Remove
拆卸步骤
开始:
- 拆卸预润滑机油泵。 请参阅拆解和组装, "预润滑机油泵 - 拆卸"。
- 安装发动机举升支架。 请参考拆解和组装, "发动机举升支架 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下将管组件固定到发动机油底壳 (4) 的螺栓和卡箍。
Show/hide table
 | |
| 图 1 | g00553584 |
典型实例 | |
Show/hide table
 | |
| 图 2 | g00553585 |
典型实例 | |
- 卸下螺栓 (2) 。 拆下隔套 (1) 。 将管组件从发动机油底壳 (4) 和发动机机油泵上拆下。
- 确保缸体和发动机油底壳 (4) 之间的所有连接已拆除。
- 将适当的起吊设备连在发动机举升支架上。 3612 发动机的重量约为 26000 kg (57300 lb)。 3616 发动机的重量约为 30000 kg (66100 lb)。 拆下将发动机油底壳 (4) 固定到缸体和端盖的螺栓 (3) 。 将发动机从底座上拆下。
- 将发动机置于支撑块上。 为了拆卸发动机油底壳，支架的最小高度应为671 mm (26.4 in)。
- 将液压千斤顶置于发动机油底壳 (4) 的每端下方。 3612 发动机油底壳的重量约为 628 kg (1385 lb)。 3616 发动机油底壳的重量约为 661 kg (1457 lb)。
Show/hide table
 | |
| 图 3 | g00553586 |
- 举升液压千斤顶，以支撑发动机油底壳 (4) 。
- 从发动机油底壳 (4) 上拆下密封垫 (5) 。
Show/hide table
 | |
| 图 4 | g00553587 |
Caterpillar Information System:
3618 Engine Crankshaft Rear Gear - Remove and Install
C9 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Service Record
3054 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Reading DC Schematics
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Symbols
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Typical Generator Abbreviations
SR500 Generators Bearing (Spherical Roller) - Lubricate
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (Generator Set) - Replace
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Relay Module - Replace
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (AC Transformer Box) - Replace
3612 and 3616 Engines Engine Oil Filter Housings - Install
3054 and 3056 Industrial and Generator Set Engines Fan Drive
C-9 Engines for Caterpillar Built Machines Unit Injector
3126B Truck Engine Engine Operation
3126B Truck Engine Refill Capacities
3126B Truck Engine Maintenance Interval Schedule
3126B Truck Engine Reference Material
Bendix DuraFlo 596 Air Compressor Air Compressor Maintenance Procedures
3612 and 3616 Engines Engine Oil Pan - Install
3056 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Connector Contact Identification of Generator Set Control
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (Generator Set) - Flash Program
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Schematics and Wiring Diagrams