Unit Injector
Show/hide table
 | |
| 图 1 | g01407502 |
(4) O 形密封圈 | |
Show/hide table
 | |
| 图 2 | g01407503 |
A-A 视图 | |
注: 利用所密封的润滑剂轻轻润滑缸盖孔径。
注: 安装喷油器总成 (1) ，使电气接头面向缸盖的排气侧。
采用以下程序安装喷油器总成：
- 使喷油器总成座入孔中。
- 拧紧距离缸盖排气侧 (5) 最近的螺栓 (2) ，直到螺栓完全就位。
- 将距离缸盖进气侧 (6) 最近的螺栓 (3) 拧紧至 12 ± 1 N·m (105 ± 9 lb in)。
Show/hide table
 | |
| 图 3 | g01407507 |
B-B 视图 (7) 支撑环 (8) O 形密封圈 (9) O 形密封圈 (10) 支撑环 | |
Show/hide table
 | |
| 图 4 | g01407504 |
喷油器总成的顶视图 | |
注: 喷油器总成顶部有四只螺栓 (11) ，用于将顶盖固定到喷油器总成上。 喷油器总成顶部有两个孔 (12) ，仅作组装之用。 不要将螺栓安装到两个螺栓孔 (12) 内。
Caterpillar Information System:
3054 and 3056 Industrial and Generator Set Engines Fan Drive
3612 and 3616 Engines Engine Oil Pan - Remove
3618 Engine Crankshaft Rear Gear - Remove and Install
C9 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Service Record
3054 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Remove
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Reading DC Schematics
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Symbols
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Typical Generator Abbreviations
SR500 Generators Bearing (Spherical Roller) - Lubricate
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (Generator Set) - Replace
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Relay Module - Replace
3126B Truck Engine Engine Operation
3126B Truck Engine Refill Capacities
3126B Truck Engine Maintenance Interval Schedule
3126B Truck Engine Reference Material
Bendix DuraFlo 596 Air Compressor Air Compressor Maintenance Procedures
3612 and 3616 Engines Engine Oil Pan - Install
3056 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Install
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Connector Contact Identification of Generator Set Control
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines EMCP Electronic Control (Generator Set) - Flash Program
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Schematics and Wiring Diagrams
3612 and 3616 Engines Engine Oil Pan - Disassemble
3618 Engine Crankshaft Front Seal and Wear Sleeve - Install