Generator - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 此步骤在G3612 发动机上进行。 这是配备发电机的所有机型的典型步骤。
- 卸下飞轮护罩 (1)、联轴器护罩 ( 2) 以及发电机护罩 ( 3)。
Show/hide table
图 2 g00589972 Show/hide table图 3 g00589973 Show/hide table图 4 g00589974 - 卸下将发动机联轴器 ( 6) 和发电机联轴器 ( 5) 固定至发电机连接板 ( 7) 的螺栓。
Show/hide table
图 5 g01039497 - 卸下滤清器 (11),以便露出发电机底座右侧的安装螺栓及销的检修孔。
注: 销孔的加工及销钉的安装完成前需进行最终对齐。
注: 标记发电机在底座上的位置。 将垫片保持在恰当位置,以便安装。
- 使用 1/2 英寸螺栓及垫圈卸下销 ( 13)。
- 拧松对齐螺栓 (8)。
- 拆下螺栓 (9)。 检查螺栓上的密封件是否损坏。 如有必要,更换密封件。
- 将适当的起吊设备连接在连杆支架 ( 4) 和 (12) 上。
- 从发电机底座上卸下发电机 ( 10)。
Show/hide table
图 1 | g01039495 |
- 将适当的起吊设备连接在连杆支架 ( 4) 和 (12) 上。
- 将发电机 (10) 安装在发电机底座上。
- 检查螺栓上的密封件是否损坏。 如有必要,更换密封件。 确保密封件安装在清洁的螺栓上。 安装八个螺栓 (9)。
- 拧紧对齐螺栓 (8)。
- 安装销 (13)。
- 安装滤清器 (11)。
Show/hide table
图 7 g00589974 Show/hide table图 8 g00589973 Show/hide table图 9 g00589972 - 卸下将发动机联轴器 ( 6) 和发电机联轴器 ( 5) 固定至发电机连接板 ( 7) 的螺栓。
Show/hide table
图 10 g01039495 - 安装发电机护罩 ( 3)、联轴器护罩 (2) 和飞轮护罩 ( 1)。
Show/hide table
图 6 | g01039497 |
Caterpillar Information System:
3044C Industrial Engine Fuel Conservation Practices
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 447 FMI 12 Fuel Control Relay Failed - Test
SR4B Generators Generator - Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 446 FMI 12 Air Shutoff Relay Failed - Test
G3612 and G3616 Engines Air Starting Motor - Disassemble
3114, 3116 and 3126 Engines Engine Overspeeds on Start
3034 Industrial Engine Cold Weather Starting
G3612 and G3616 Engines Air Inlet Elbow - Remove and Install
G3612 and G3616 Engines Air Inlet Choke - Assemble
3114, 3116 and 3126 Engines Engine Misfires, Knocks, or Is Unstable (at Idle Only)
G3612 and G3616 Engines Air Inlet Choke - Disassemble
G3612 and G3616 Engines Air Inlet Choke - Remove
3500B Engines Water Pump - Install
G3304 and G3306 Engines Valve Cover
3126B and 3126E On-highway Engines Unit Injector Hydraulic Pump - Install
G3304 and G3306 Engines Valve Cover
3306C Engines for Caterpillar Built Machines Gear Group (Front)
G3304 and G3306 Engines Engine Support
Generator Set Load Sensor Droop - Adjust
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 560 FMI 11 CAT Data Link Failure Mode Not Identified - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines SP Fault Code - Troubleshoot
3512B Marine Auxiliary Engine MID 036 - CID 0289 - FMI 13 Unfiltered Fuel Pressure calibration required
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
3512B Marine Auxiliary Engine MID 036 - CID 0542 - FMI 13 Unfiltered Engine Oil Pressure cal required