Fuel Conservation Practices
发动机的效率会影响燃油经济性。 卡特彼勒设计和制造技术为所有应用提供最大燃油效率。 遵循建议的程序以便获得发动机使用寿命期的最佳性能。
- 避免燃油溢出。
燃油受热会膨胀。 燃油可能会从燃油箱溢出。 检查燃油管路是否有渗漏。 对燃油管路进行所需的维修。
- 知道不同燃油的特性。 只使用推荐的燃油。
- 避免不必要的怠速运转。
使发动机停机而不是长时间怠速运行。
- 经常观察保养指示器。 保持空气滤清器滤芯清洁。
- 保持电气系统状态良好。
一 在组装 个坏的蓄电池单元将使交流发电机过度工作。 这将消耗额外的功率和燃油。
- 确保皮带调整适当。 皮带应状况良好。
- 确保所有软管连接紧密。 连接处不应泄漏。
- 确保被驱动设备状况良好。
- 冷态发动机消耗过多的燃油。 尽可能利用来自水套水系统和排气系统的热量。 保持冷却系统部件清洁和得到良好维护。 决不能运转未安装水温调节器的发动机。 所有这些项目将有助于保持运行温度。
- 发动机信息铭牌上刻印了燃油系统设定值和可运行海拔高度的限制。 如果发动机被移动到更高的海拔高度,设定值必须由卡特彼勒代理商来修改。 修改设定值将有助于发动机提供最大效率。 发动机可以在高海拔安全运行,但发动机的输出马力将减少。 燃油设定值应由卡特彼勒代理商修改,以便获得额定的马力。
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 447 FMI 12 Fuel Control Relay Failed - Test
SR4B Generators Generator - Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 446 FMI 12 Air Shutoff Relay Failed - Test
G3612 and G3616 Engines Air Starting Motor - Disassemble
3114, 3116 and 3126 Engines Engine Overspeeds on Start
3034 Industrial Engine Cold Weather Starting
G3612 and G3616 Engines Air Inlet Elbow - Remove and Install
G3612 and G3616 Engines Air Inlet Choke - Assemble
3114, 3116 and 3126 Engines Engine Misfires, Knocks, or Is Unstable (at Idle Only)
G3612 and G3616 Engines Air Inlet Choke - Disassemble
G3612 and G3616 Engines Air Inlet Choke - Remove
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 445 FMI 12 Run Relay Failed - Test
G3612 and G3616 Engines Generator - Remove and Install
3500B Engines Water Pump - Install
G3304 and G3306 Engines Valve Cover
3126B and 3126E On-highway Engines Unit Injector Hydraulic Pump - Install
G3304 and G3306 Engines Valve Cover
3306C Engines for Caterpillar Built Machines Gear Group (Front)
G3304 and G3306 Engines Engine Support
Generator Set Load Sensor Droop - Adjust
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 560 FMI 11 CAT Data Link Failure Mode Not Identified - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines SP Fault Code - Troubleshoot
3512B Marine Auxiliary Engine MID 036 - CID 0289 - FMI 13 Unfiltered Fuel Pressure calibration required
3126B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install