Air Inlet Choke - Assemble
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
图 1 | g00590713 |
- 将轴 (2)插入阻风门的壳体 ( 5) 中。
- 安装阻风门板 (4)。 安装阻风门板时,使安装螺栓 ( 1) 保持在拧松状态。 安装止推垫圈 (3)。 安装螺栓。 将螺栓拧紧至扭矩为
47 ± 9 N·m (35 ± 7 lb ft) 。 完全关闭阻风门板。 将阻风门板的安装螺栓拧紧至扭矩12 ± 3 N·m (9 ± 2 lb ft) 。 - 安装板和两个螺栓。 将两个螺栓拧紧至扭矩
47 ± 9 N·m (35 ± 7 lb ft) 。 - 将阻风门板组装在轴上后,安装调整螺栓直至其与挡板接触。 应再将调整螺栓拧紧 90 度。 将调整螺母拧紧至扭矩
25 ± 6 N·m (18 ± 5 lb ft) 。注: 拧紧锁紧螺母时,调整螺钉不能转动。
结束:
- 安装阻风门。
Caterpillar Information System:
3114, 3116 and 3126 Engines Engine Misfires, Knocks, or Is Unstable (at Idle Only)
G3612 and G3616 Engines Air Inlet Choke - Disassemble
G3612 and G3616 Engines Air Inlet Choke - Remove
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 445 FMI 12 Run Relay Failed - Test
G3612 and G3616 Engines Junction Box (Hydrax) - Remove and Install
C9 On-Highway Truck Engines Unit Injector Hydraulic Pump - Remove
Generator Set Load Sensor Phasing - Adjust
3114, 3116 and 3126 Engines Alternator Noise
G3612 and G3616 Engines Hydraulic Tank (Hydrax) - Remove and Install
G3612 and G3616 Engines Hydraulic Oil Pump (Hydrax) - Remove and Install
3500B Engines Air Inlet Manifold - Remove and Install
G3612 and G3616 Engines Caterpillar Ignition System (CIS) Module - Remove and Install
G3612 and G3616 Engines Air Inlet Elbow - Remove and Install
3034 Industrial Engine Cold Weather Starting
3114, 3116 and 3126 Engines Engine Overspeeds on Start
G3612 and G3616 Engines Air Starting Motor - Disassemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 446 FMI 12 Air Shutoff Relay Failed - Test
SR4B Generators Generator - Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 447 FMI 12 Fuel Control Relay Failed - Test
3044C Industrial Engine Fuel Conservation Practices
G3612 and G3616 Engines Generator - Remove and Install
3500B Engines Water Pump - Install
G3304 and G3306 Engines Valve Cover
3126B and 3126E On-highway Engines Unit Injector Hydraulic Pump - Install