Hydraulic Tank (Hydrax) - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
- 使用液压油箱底部上的排放阀 (1) 排放油箱。 确保可以使用适当的容器存储液压油。
Show/hide table
图 2 g00597290 - 从液压油箱 (2) 上拆下管 (3) 和 (4)。
- 从液压油箱上拆下四颗螺栓 (5)。
- 要拆卸安装支架,拆下用于固定支架的六颗螺栓。
Show/hide table
图 3 g00867388 - 逆时针转动滤清器 (8),以便拆下滤清器。
- 从滤清器组件上拆下管 (7) 和 (9)。
- 拆下用于固定滤清器组件的四颗螺栓 (6)。
Show/hide table
图 4 g00867389 - 拆下用于固定滤清器组件安装支架的四颗螺栓 (10)。
Show/hide table
图 5 g00867390 - 拆下螺栓 (14)。 拆下用于固定蓄能器 (11) 的卡箍 (12)。 拆下压力管 (13)。 拆下蓄能器。
- 拆下单路单向阀 (15)。
Show/hide table
图 1 | g00597318 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 安装单路单向阀 (15)。 确保箭头指向发动机后部。
注: 安装之前,必须检查蓄能器。 安装之后,也必须充注蓄能器。 请参考发动机新闻, 1æ 1999, 第 25 , "检查和充注 Hydrax 蓄能器的步骤"以了解更多信息。
- 安装蓄能器 (11)。 安装压力管 (13)。 安装用于固定蓄能器的卡箍 (12)。 安装螺栓 (14)。
Show/hide table
图 7 g00867389 - 安装滤清器组件安装支架。 安装用于固定安装支架的四颗螺栓 (10)。
Show/hide table
图 8 g00867388 - 定位滤清器组件。 安装用于固定滤清器组件的四颗螺栓 (6)。
- 将管 (7) 和 (9) 安装到滤清器组件上。
- 顺时针转动滤清器 (8),以便安装滤清器。
Show/hide table
图 9 g00597290 - 如果拆下了安装支架,则将支架定位到发动机上。 安装用于固定支架的六颗螺栓。
- 安装液压油箱 (2)。 安装用于固定液压油箱的四颗螺栓 (5)。
- 将管 (3) 和 (4) 安装到液压油箱上。
Show/hide table
图 10 g00597318 - 确保液压油箱底部上的排放阀 (1) 处于关闭状态。 将液压油箱加注至正确液位。 请参考操作和保养手册以了解更多信息。
Show/hide table
图 6 | g00867390 |
Caterpillar Information System:
G3612 and G3616 Engines Hydraulic Oil Pump (Hydrax) - Remove and Install
3500B Engines Air Inlet Manifold - Remove and Install
G3612 and G3616 Engines Caterpillar Ignition System (CIS) Module - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 444 FMI 12 Starting Motor Relay Failed - Test
G3612 and G3616 Engines Actuator (Hydrax) - Assemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 443 FMI 12 Crank Termination Relay Failed - Test
G3612 and G3616 Engines Actuator (Hydrax) - Disassemble
G3612 and G3616 Engines Actuator (Hydrax) - Install
G3612 and G3616 Engines Actuator (Hydrax) - Remove
3114, 3116 and 3126 Engines Excessive Blue Smoke
C-15, C-16 and C-18 Truck Engines Engine Oil Pressure Sensor - Remove and Install
3512B Marine Auxiliary Engine Electrical Power Supply
3114, 3116 and 3126 Engines Alternator Noise
Generator Set Load Sensor Phasing - Adjust
C9 On-Highway Truck Engines Unit Injector Hydraulic Pump - Remove
G3612 and G3616 Engines Junction Box (Hydrax) - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 445 FMI 12 Run Relay Failed - Test
G3612 and G3616 Engines Air Inlet Choke - Remove
G3612 and G3616 Engines Air Inlet Choke - Disassemble
3114, 3116 and 3126 Engines Engine Misfires, Knocks, or Is Unstable (at Idle Only)
G3612 and G3616 Engines Air Inlet Choke - Assemble
G3612 and G3616 Engines Air Inlet Elbow - Remove and Install
3034 Industrial Engine Cold Weather Starting
3114, 3116 and 3126 Engines Engine Overspeeds on Start