Water Pump - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
C     | 5P-9722     | 油封起子     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 利用压具将轴和轴承装入皮带轮 (3) 中。 安装轴,直到轴与皮带轮 (3) 的端面齐平为止。
Show/hide table
图 1 | g00614283 |
- 将轴、轴承和皮带轮 (3) 作为一个整体压入水泵壳中。 皮带轮 (3) 前端与水泵壳加工面间的距离必须为 103.8 ± 0.3 mm (4.09 ± 0.01 in)。
注: 关于皮带轮 (3) 再利用性的信息,请参阅再利用零件和修补操作指南, SEBF8046, "铸铁和钢制皮带轮"。
- 利用工具 (C) 将密封 (5) 装入水泵壳中。
Show/hide table
图 2 | g01004707 |
- 利用压具将叶轮 (4) 安装到水泵轴上。 安装叶轮,直到叶轮与水泵机加工表面之间的距离为 0.75 ± 0.25 mm (0.030 ± 0.010 in)。
Show/hide table
图 3 | g00614288 |
- 将新密封垫安装到水泵后盖和水泵壳之间。 将密封垫和盖定位到水泵壳上。 安装螺栓 (2) 和垫圈。
Show/hide table
图 4 | g00614231 |
- 将新 O 形密封圈 (1) 安装到后盖内。
End By: 安装水泵。 请参阅 拆解和组装, "水泵 - 安装"。
Caterpillar Information System:
C-15, C-16 and C-18 Truck Engines Water Temperature Regulator - Remove and Install
SR4B Generators Resistor - Test
SR4B Generators Winding - Test
3126B Engines for Caterpillar Built Machines Water Pump - Disassemble
3500B Engines Camshaft Bearings - Install
3524B Engine for Caterpillar Built Machines Camshaft Bearings - Remove
3126B and 3126E On-highway Engines Water Pump - Install
3034 Marine Engine Water Temperature Regulator Housing
3126 Truck Engine Military Water Pump - Remove
G3612 and G3616 Engines Valve Lifter - Assemble
G3612 and G3616 Engines Valve Lifter - Disassemble
G3612 and G3616 Engines Valve Lifter - Install
3054B Industrial Engine Reference Material
3114, 3116 and 3126 Engines Air Inlet Heater - If Equipped
3114, 3116 and 3126 Engines Little or No Valve Lash
3114, 3116 and 3126 Engines Loss of Coolant
SR4B Generators Leads - Connect
3406E Generator Set Engines Customer Specified Parameters
3126 Truck Engine Military Engine Oil Pump - Remove
3126 Truck Engine Military Engine Oil Pump - Install
3126 Truck Engine Military Engine Oil Pump - Disassemble
SR4B Generators Exciter Field - Flash
C-9 Engines for Caterpillar Built Machines Lifter Group
SR4B Generators Generator - Dry