Exciter Field - Flash
Show/hide table
图 1 | g00874825 |
自励磁发电机配线图 (CR1-C6) 二级管 (CR7) 变阻器 (L1) 励磁机磁场(定子) (L2) 励磁机电枢(转子) (L3) 主磁场(转子) (L4) 主电枢(定子) (RFA) 旋转磁场总成 (CT1) 选装的电压降变压器 (T0、T1、T2、T3、T7、T8、T9) 发电机端子 |
自励磁发电机可能失去通常存在于励磁机磁场 (L1) 和主磁场 (L3) 的残留磁性。 需要残留磁性起动发电流程。 可使用直流电起励励磁机磁场 (L1) ,从而恢复磁性。 可使用 6 VDC 蓄电池供应直流电。
Show/hide table
注意 |
---|
请勿闪断永久先导励磁(PMPE)发电机。 可能损坏发电机组。 |
有两种方法起励磁场:
- 静态起励(发动机停机时)
- 动态起励(发动机运行时)
静态起励(发动机停机时)
Show/hide table
所需工具     | |
工具     | 数量     |
6 VDC 蓄电池     | 1     |
- 关闭发动机。
- 在电压调节器处,将导线 F1 GEN 从端子 F1 上断开,然后将导线 F2 GEN 从端子F2 上断开。
- 将 6 伏电源的正极电缆连接到导线 F1 GEN。
- 将 6 伏电源的负极电缆瞬时放到导线 F2 GEN 上(两次或三次)。
注: 不要让负极电缆与导线 F2 GEN 接触超过一秒或两秒。
- 连接之前断开的所有导线。
动态起励(发动机运行时)
Show/hide table
图 2 | g00614470 |
动态起励电路 (1) 蓄电池(≤ 6 VDC) (2) 二极管 (3) 红色测试引线 "+" (4) 黑色测试引线 "-" |
Show/hide table
所需工具     | ||
零件号     | 工具     | 数量     |
6V-7070     | 数字式万用表     | 1     |
9P-5153     | 二极管 (MR-504)     |
1     |
    | 动态起励电路     | 1     |
- 建立如图 2 所示的动态起励电路。
- 关闭发动机。
- 将万用表(设在 ACV)连接到电压调节器上的端子 20 和 22。
- 起动发动机并以低怠速运转发动机。
- 将动态起励电路的红色引线与端子 F1 相接。
Show/hide table
注意 |
---|
闪磁电路的测试引线接通端子的时间不要超过必要的时间。 时间过长可能导致电压过高。 电压过高可能导致发电机损坏,也可能导致闪磁电路损坏。 |
- 监控电压表。 将黑色引线与动态起励电路的端子 F2 相接。
- 电压表显示电压增加时,将测试引线从端子 F1 和 F2 上拆下。 如果 5 至 10 秒内发电机电压未增加,则将测试引线从端子 F1 和 F2 上拆下。
Caterpillar Information System:
3126 Truck Engine Military Engine Oil Pump - Disassemble
3126 Truck Engine Military Engine Oil Pump - Install
3126 Truck Engine Military Engine Oil Pump - Remove
3406E Generator Set Engines Customer Specified Parameters
SR4B Generators Leads - Connect
3114, 3116 and 3126 Engines Loss of Coolant
3114, 3116 and 3126 Engines Little or No Valve Lash
3114, 3116 and 3126 Engines Air Inlet Heater - If Equipped
3054B Industrial Engine Reference Material
3126B Engines for Caterpillar Built Machines Water Pump - Assemble
C-15, C-16 and C-18 Truck Engines Water Temperature Regulator - Remove and Install
SR4B Generators Resistor - Test
C-9 Engines for Caterpillar Built Machines Lifter Group
SR4B Generators Generator - Dry
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test
G3304 and G3306 Engines Valve Mechanism
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 248 FMI 9 CAT Data Link Abnormal Update - Test
G3612 and G3616 Engines Cylinder Head - Assemble
3126B Engines for Caterpillar Built Machines Unit Injector Sleeve - Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 330 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
3114, 3116 and 3126 MUI Engine Governors Governor (Type VI) - Disassemble
3114, 3116 and 3126 Engines Low Engine Oil Pressure
3114, 3116 and 3126 Engines Low Power