Engine Oil Pump - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
B     | 1P-2320     | 组合式拉拔器     | 1     |
开始:
- 拆卸发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
注: 有关发动机机油泵可再用性信息,请参阅再使用零件和修补操作指南, SEBF8167, "3114 和 3116 发动机修复步骤"。
- 从吸油管 (2) 的管组件上拆下螺栓,然后从发动机机油泵上拆下密封垫。 从发动机机油泵上拆下螺栓和出口弯头 (1) 。
Show/hide table
图 1 | g00614664 |
- 将螺栓 (3) 、垫圈 (4) 和惰轮 (5) 从机油泵上拆下。
Show/hide table
图 2 | g00614677 |
- 利用工具 (A) 和适当的压具将轴承从惰轮 (5) 上拆下。
Show/hide table
图 3 | g00614683 |
- 将发动机机油泵轴 (6) 从机油泵体组件 (7) 上拆下。
- 利用工具 (B) 拆下驱动齿轮 (8) 。
- 拆下螺栓 (10) 。 将机油泵壳 (9) 从机油泵壳体组件 (7) 上分离。
Show/hide table
图 4 | g00614689 |
- 将轴组件 (11) 和 (12) 从机油泵壳 (9) 上拆下。
Show/hide table
图 5 | g00614694 |
Show/hide table
注意 |
---|
从泵壳上拆下驱动轴之前,确保驱动轴上没有毛刺。 如果驱动轴上有毛刺,很可能会划伤泵壳内孔。 |
- 将以下各项从机油泵体组件 (7) 上拆下:螺栓和垫圈, 弹簧 (14) 和 机油卸压柱塞 (13)
Show/hide table
图 6 | g00824021 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
Caterpillar Information System:
3126 Truck Engine Military Engine Oil Pump - Install
3126 Truck Engine Military Engine Oil Pump - Remove
3406E Generator Set Engines Customer Specified Parameters
SR4B Generators Leads - Connect
3114, 3116 and 3126 Engines Loss of Coolant
3114, 3116 and 3126 Engines Little or No Valve Lash
3114, 3116 and 3126 Engines Air Inlet Heater - If Equipped
3054B Industrial Engine Reference Material
3126B Engines for Caterpillar Built Machines Water Pump - Assemble
C-15, C-16 and C-18 Truck Engines Water Temperature Regulator - Remove and Install
SR4B Generators Resistor - Test
SR4B Generators Winding - Test
SR4B Generators Exciter Field - Flash
C-9 Engines for Caterpillar Built Machines Lifter Group
SR4B Generators Generator - Dry
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test
G3304 and G3306 Engines Valve Mechanism
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 248 FMI 9 CAT Data Link Abnormal Update - Test
G3612 and G3616 Engines Cylinder Head - Assemble
3126B Engines for Caterpillar Built Machines Unit Injector Sleeve - Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 330 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
3114, 3116 and 3126 MUI Engine Governors Governor (Type VI) - Disassemble
3114, 3116 and 3126 Engines Low Engine Oil Pressure