Leads - Connect
到端子连接条的发电机引线
Show/hide table
图 1 | g00613767 |
端子连接条 |
Show/hide table
图 2 | g00614345 |
端子连接条引线连接 (1) 发电机引线 (2) 端子连接条(母线) (3) 电镀垫圈 |
将发电机引线 (1) 以以下方法附接到端子连接条 (2) :
- 多根引线附接到母线时,将引线放在母线的两端。 在螺栓头和螺母下方使用平电镀垫圈 (3) 。
- 将引线连接到母线后,将所有发电机相位引线规整。 将这些引线绑在一起。
确保非绝缘连接(相位对相位及相位对地)间至少有 25 mm (1.0 in) 间隙。
发电机引线至另一引线
Show/hide table
图 3 | g00614361 |
引线至引线连接(中压及以下的发电机) (1) 电镀垫圈 |
Show/hide table
所需工具     | ||
零件号     | 工具     | 数量     |
5N-4685     | 浸漆细麻布电气胶带 15000 伏额定电压 105 °C (221.0 °F) 额定温度     |
1     |
5N-4686     | 黑色乙烯基塑料电气胶带 −40 °C (−40.0 °F) - 80 °C (176.0 °F) 额定温度     |
1     |
将发电机引线连接在一起或将发电机引线连接到负载引线时,使用以下步骤:
- 通过在螺栓头和螺母下方使用平电镀垫圈 (1) 将发电机引线固定在一起。
- 使用两层浸漆细麻布高压胶带。 缠绕胶带时,胶带必须重叠。 重叠部分必须为胶带宽度的 50%。 胶带缠绕必须在导线绝缘层上延长 "B"。 长度 "B" 等于 25 mm (1.0 in)。
- 在浸漆细麻布高压胶带上再使用两层乙烯基塑料电气胶带。 胶带缠绕必须在导线绝缘层上延长 "A"。 长度 "A" 等于 51 mm (2.0 in)。
- 发电机引线不得解除接线盒的金属片或任何旋转零件。 将各发电机相位的引线规整。 用电缆扎带将引线固定在一起。
Caterpillar Information System:
3114, 3116 and 3126 Engines Loss of Coolant
3114, 3116 and 3126 Engines Little or No Valve Lash
3114, 3116 and 3126 Engines Air Inlet Heater - If Equipped
3054B Industrial Engine Reference Material
3126B Engines for Caterpillar Built Machines Water Pump - Assemble
C-15, C-16 and C-18 Truck Engines Water Temperature Regulator - Remove and Install
SR4B Generators Resistor - Test
SR4B Generators Winding - Test
3126B Engines for Caterpillar Built Machines Water Pump - Disassemble
3500B Engines Camshaft Bearings - Install
3524B Engine for Caterpillar Built Machines Camshaft Bearings - Remove
3126B and 3126E On-highway Engines Water Pump - Install
3406E Generator Set Engines Customer Specified Parameters
3126 Truck Engine Military Engine Oil Pump - Remove
3126 Truck Engine Military Engine Oil Pump - Install
3126 Truck Engine Military Engine Oil Pump - Disassemble
SR4B Generators Exciter Field - Flash
C-9 Engines for Caterpillar Built Machines Lifter Group
SR4B Generators Generator - Dry
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test
G3304 and G3306 Engines Valve Mechanism
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 248 FMI 9 CAT Data Link Abnormal Update - Test
G3612 and G3616 Engines Cylinder Head - Assemble