Valve Lifter - Assemble
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将挺杆杆体 (1) 放置于液压机内。
- 将发动机机油涂敷于挺杆 ( 1) 的内孔和适配器 ( 2) 的孔上。 将适配器 ( 2) 按压至杆体 (1) 内。 装配后,适配器的顶部应与杆体 ( 1) 的顶部齐平。
Show/hide table
图 2 g00570916 注: 安装销后,将垫片放置于挺杆和滚轮间。 以防杆体的叉具弯曲,这一点非常必要。
- 将滚轮 (5) 放置于挺杆 ( 4) 的叉具间。 将这两个部件放置于压力机内,并使锁线槽位于顶部。
- 将导线安装至销 ( 3) 内,且两端超出的长度相等。
- 用清洁的发动机机油润滑销 ( 3)。
- 将导线与挺杆 (4) 的叉具上的槽对齐。
- 将销 (3) 压缩至挺杆 ( 4) 和滚轮 (5) 中。
- 将推杆镶圈安装在挺杆杆体 ( 4) 内。
- 将进气挺杆杆体和排气挺杆杆体的温度升至
177 °C (350 °F) 。 将销的温度降至−60 °C (−76 °F) 。Show/hide table操作已经加热的零件时要坚持戴防护手套。
Show/hide table图 3 g00570917 - 将新导向弹簧 (9) 和导向弹簧 ( 11) 安装在挺杆上。
注: 如果从阀挺杆上卸下导向弹簧,则不能再次使用导向弹簧。
Show/hide table图 4 g00626748 图中所示的阀挺杆未安装滚子。 - 将镶圈 (13)安装在杆体 ( 14)内,并使挺杆杯正面向外。 安装新的 O 型密封圈护圈 ( 12),以便将镶圈固定到位。
- 将以下挺杆浸入清洁的发动机机油内: (7), (8) 和 (10)。
- 将阀挺杆 (7)和 ( 10)安装在原始位置。 安装阀挺杆,以便导向弹簧处于合适的位置。
注: 使用大钳子压缩导向弹簧 ( 11),以便将阀挺杆组件安装至阀导管 ( 6) 内。
- 安装进气阀挺杆 ( 8)。
Show/hide table
图 1 | g00570915 |
结束:
- 安装阀挺杆组件。
- 安装推杆。
- 检查气门间隙。
Caterpillar Information System:
G3612 and G3616 Engines Valve Lifter - Disassemble
G3612 and G3616 Engines Valve Lifter - Install
Generator Set Load Sensor Installation Requirements
G3612 and G3616 Engines Valve Lifter - Remove
3524B Engine for Caterpillar Built Machines Crankshaft - Install
3126B Engines for Caterpillar Built Machines Crankshaft Wear Sleeve (Rear) - Remove - If Equipped
Electronic Modular Control Panel II (EMCP II) For MUI Engines Troubleshooting Diagnostic Codes
3512B Marine Auxiliary Engine Flexible Coupling
3524B Engine for Caterpillar Built Machines Crankshaft - Remove
3512B Marine Auxiliary Engine Electrical Connectors and Functions
3126B Engines for Caterpillar Built Machines Unit Injector Sleeve - Remove
3512B Marine Auxiliary Engine ECM/Personality Module
3126 Truck Engine Military Water Pump - Remove
3034 Marine Engine Water Temperature Regulator Housing
3126B and 3126E On-highway Engines Water Pump - Install
3524B Engine for Caterpillar Built Machines Camshaft Bearings - Remove
3500B Engines Camshaft Bearings - Install
3126B Engines for Caterpillar Built Machines Water Pump - Disassemble
SR4B Generators Winding - Test
SR4B Generators Resistor - Test
C-15, C-16 and C-18 Truck Engines Water Temperature Regulator - Remove and Install
3126B Engines for Caterpillar Built Machines Water Pump - Assemble
3054B Industrial Engine Reference Material
3114, 3116 and 3126 Engines Air Inlet Heater - If Equipped