Exhaust Elbow - Remove and Install
Show/hide table
需要的工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7573 | 连杆支架 | 2 |
开始:
- 拆卸涡轮增压器。 参考拆解与组装, "涡轮增压器 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在排气弯管 (1)的顶部安装工具 (A)。 将适当起吊设备连在工具 (A)上。 排气弯管 (1)的重量约为
48 kg (106 lb) 。 - 拆卸螺栓 (2)。 从发动机上提升排气弯管 (1)。
Show/hide table
图 2 g00615016 - 拆卸螺栓和卡箍 (3)。 从管 (5)的每一端拆卸螺栓和卡箍 (4)。 拆卸管组件 (5)。 检查管组件端 (5)的密封件。 如果密封件被损坏或发生变质,则安装一个新的密封件。
Show/hide table
图 3 g00615017 - 将适当起吊设备连在支架 (7)上。 支架 (7)的重量约为
117 kg (257 lb) 。 - 拆卸螺栓 (6)。 拆卸支架 (7)。
Show/hide table
图 1 | g00615014 |
Show/hide table
需要的工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7573 | 连杆支架 | 2 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将适当起吊设备连在支架 (7)上。 支架 (7)的重量约为
117 kg (257 lb) 。 将支架 (7)置于发动机上。 - 安装螺栓 (6).
Show/hide table
图 5 g00615016 注: 确保密封件安装在管 (5)的末端。
- 固定管 (5)并在管 (5)的每一端安上螺栓和卡箍 (4)。 安装螺栓和卡箍 (3)。
Show/hide table
图 6 g00615014 - 在排气弯管 (1)的顶部安装工具 (A) 。 将适当起吊设备连在工具 (A)上。 排气弯管 (1)的重量约为
48 kg (106 lb) 。 定位排气弯管 (1)。 - 安装螺栓 (2)。
Show/hide table
图 4 | g00615017 |
结束:
- 安装涡轮增压器。 参考拆解与组装, "涡轮增压器 - 安装"。
Caterpillar Information System:
G3606 and G3608 Engines Junction Box (Hydrax) - Remove and Install
G3500 Engines Carburetor - Remove - Low Pressure
G3500 Engines Carburetor - Remove - High Pressure
3064 and 3066 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
G3500 Engines Exhaust Elbow - Remove and Install
3612 and 3616 Engines Water Pump - Sea Water
3612 and 3616 Engines Water Pump
G3500 Engines Exhaust Elbow - Remove and Install
3500B Engines Expansion Tank - Remove and Install
G3500 Engines Exhaust Bypass Valve - Remove and Install
3034 Engine for Caterpillar Built Machines Turbocharger - Remove
3406E and 3456 Generator Set Engines Alternator - Remove and Install
3524B Engine for Caterpillar Built Machines Crankcase Breather - Remove and Install
G3500 Engines Carburetor - Remove - Low Pressure
G3500 Engines Carburetor - Install - High Pressure
G3500 Engines Carburetor - Install - Low Pressure
G3500 Engines Carburetor - Install - Low Pressure
G3606 and G3608 Engines Hydraulic Oil Pump (Hydrax) - Remove and Install
G3500 Engines Carburetor - Disassemble - High Pressure
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Harness Code - Troubleshoot
G3606 and G3608 Engines Hydraulic Tank (Hydrax) - Remove and Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Front Housing and Covers
3500B Engines Air Starting Motor - Remove
G3500 Engines Carburetor - Assemble - High Pressure