Electric Starting Motor - Remove and Install
- 从电磁阀 (1)和起动马达 (2)上断开导线和电线。
如果发动机有两个起动马达,断开两个电磁阀和起动马达之间的导线。
- 将适当的起重机连在起动马达上。 起动马达重约为
30 kg (66 lb) 。 - 拆卸三个螺栓 (3)。 拆下起动马达。 从起动马达和飞轮壳体之间的接头上拆卸密封垫。
Show/hide table
在进行维修作业前断开蓄电池。 |
注: 断开导线和电线前,在相应的接头上正确标记项目以确保正确组装。
Show/hide table
图 1 | g00597378 |
- 检查起动马达和飞轮壳体间接头的密封垫。 如有必要,更换一个新的密封垫。
- 将适当的起重机连在起动马达上。 起动马达重约为
30 kg (66 lb) 。Show/hide table图 2 g00597378 - 在起动马达的盖上安装密封垫。 提升起动马达使之就位于安装位置。 安装三个螺栓 (3)。
- 将导线和电线连接到电磁阀 (1)和起动马达 (2)。
如果发动机有两个起动马达,连接两个电磁阀和起动马达之间的导线。
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 330 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
G3500 Engines Exhaust Manifold - Install - Water Cooled
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 269 FMI 4 Sensor Power Supply Voltage Below Normal - Test
G3500 Engines Exhaust Manifold - Remove - Water Cooled
G3606 and G3608 Engines Turbocharger - Assemble
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 269 FMI 3 Sensor Power Supply Voltage Above Normal - Test
3500B Engines Alternator - Remove and Install
G3500 Engines Aftercooler - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 248 FMI 9 CAT Data Link Abnormal Update - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test
3114, 3116, and 3126 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
3406E and 3456 Generator Set Engines Alternator - Remove and Install
3034 Engine for Caterpillar Built Machines Turbocharger - Remove
G3500 Engines Exhaust Bypass Valve - Remove and Install
3500B Engines Expansion Tank - Remove and Install
G3500 Engines Exhaust Elbow - Remove and Install
3612 and 3616 Engines Water Pump
3612 and 3616 Engines Water Pump - Sea Water
G3500 Engines Exhaust Elbow - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
G3500 Engines Carburetor - Remove - High Pressure
G3500 Engines Carburetor - Remove - Low Pressure
G3606 and G3608 Engines Junction Box (Hydrax) - Remove and Install