Alternator - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从交流发电机 (5)上断开线束组件 (2)、 (3)和 (4)。
- 松开调节螺母 (1)以松开皮带。
Show/hide table
图 2 g00599024 - 拆卸螺母和垫圈 (6)以拆卸皮带护罩 (7)。
- 从交流发电机皮带轮上拆下皮带 (8)。
- 拆卸螺栓 (9)以断开调节杆上的交流发电机。
- 拆卸螺栓 (10)以断开支架上的交流发电机。 拆卸交流发电机 (5)。
Show/hide table
图 1 | g00599021 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将交流发电机 (5)放在支架上。 安装螺栓 (9)和 (10)以将交流发电机 (5)固定在适当的位置。 此时不要拧紧螺栓。
- 在交流发电机的皮带轮上安装 (8)皮带。
Show/hide table
图 4 g00599021 - 调节皮带张紧度。 请参阅技术规范, "皮带张紧力表"。 为了调整皮带张紧度,调节螺母 (1)。 拧紧调节螺母 (1)。
- 调节皮带张紧度后,安装皮带护板 (7)。 用螺母和垫圈 (6)将皮带护罩紧固到螺栓 (9)和 (10)上。
- 连接线束组件 (2)、 (3)和 (4)。
Show/hide table
图 3 | g00599024 |
Caterpillar Information System:
G3500 Engines Aftercooler - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 248 FMI 9 CAT Data Link Abnormal Update - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test
3114, 3116, and 3126 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
3126B Marine Engine Vibration Damper
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 168 FMI 4 Electrical System Voltage Below Normal - Test
Installation Instructions for the Accessory Module Support{7060} Installation Instructions for the Accessory Module Support{7060}
3500B Engines and 3500 Engines with EUI Option Speed Control
3500B Engines Air Cleaner - Remove and Install
3406E and 3456 Generator Set Engines Electric Starting Motor - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 269 FMI 3 Sensor Power Supply Voltage Above Normal - Test
G3606 and G3608 Engines Turbocharger - Assemble
G3500 Engines Exhaust Manifold - Remove - Water Cooled
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 269 FMI 4 Sensor Power Supply Voltage Below Normal - Test
G3500 Engines Exhaust Manifold - Install - Water Cooled
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 330 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test
3500B Engines Electric Starting Motor - Remove and Install
3406E and 3456 Generator Set Engines Alternator - Remove and Install
3034 Engine for Caterpillar Built Machines Turbocharger - Remove
G3500 Engines Exhaust Bypass Valve - Remove and Install
3500B Engines Expansion Tank - Remove and Install
G3500 Engines Exhaust Elbow - Remove and Install