Engine Oil Pump - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7573 | Link Bracket | 2 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Show/hide table
Illustration 1 g01253311 - Remove bolts (2), (3), and (4). Remove adapter (1).
Show/hide table
Illustration 2 g01253313 - Remove bolts (7). Remove elbow (6) and tube (5).
- Remove the flange and tube (8) from the engine oil cooler bonnet.
Show/hide table
Illustration 3 g00591832 - Attach Tooling (A) and a suitable lifting device to engine oil pump (9). The weight of engine oil pump (9) is approximately
39 kg (86 lb) . - Remove bolts (10) and (11). Disconnect clip (12).
- Remove engine oil pump (9).
Caterpillar Information System:
3500B Engines Engine Oil Cooler - Assemble
3500B Engines Engine Oil Cooler - Disassemble
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0545 - FMI 05 Ether Start Relay open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0545 - FMI 06 Ether Start Relay short to ground
G3500 Engines Engine Oil Cooler - Install
3406E and 3456 Generator Set Engines Front Cover - Remove
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0248 - FMI 09 Cat Data Link not communicating
3304B and 3306B Engines for Caterpillar Built Machines Cylinder Head - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0274 - FMI 13 Atmospheric Pressure calibration required
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0274 - FMI 04 Atmospheric Pressure short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0263 - FMI 04 Digital Sensor Supply short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0263 - FMI 03 Digital Sensor Supply short to +batt
3406E and 3456 Generator Set Engines Front Cover - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0827 - FMI 08 Left Exhaust Temperature signal abnormal
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0261 - FMI 13 Engine Timing calibration required
G3500 Engines Engine Oil Pump - Install
3408E and 3412E Engines for Caterpillar Built Machines Compression - Test
G3500 Engines Engine Oil Pump - Disassemble
3176C and 3196 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
3408E and 3412E Engines for Caterpillar Built Machines Cooling System - Inspect
G3500 Engines Engine Oil Pump - Assemble
3176C and 3196 Engines for Caterpillar Built Machines Cooling System - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C15 Petroleum Generator Set Engines Water Temperature Regulator - Test