Engine Oil Cooler - Assemble
注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。
注: 利用正在使用的机油润滑 O 形密封圈。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保机油冷却器芯 (3) 内的管清洁。
Show/hide table
图 2 g01253217 - 必要时,安装 O 形密封圈和盖 (14)。
- 必要时,安装 O 形密封圈和排放塞 (15)。
- 按拆解程序中记下的方位将密封垫和底盖 (6) 安装到机油冷却器芯 (3) 上。 安装螺栓。
Show/hide table
图 3 g01004704 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将旁通阀 (12) 和弹簧 (11) 装入弯头 (5) 中。 安装 O 形密封圈 (10) 并用干净的机油润滑 O 形密封圈。 安装盖 (9) 和螺栓 (13)。
Show/hide table
图 4 g01004658 - 将 O 形密封圈安装到管 (7) 上,并利用干净的机油润滑 O 形密封圈。 将管 (7) 和法兰 (8) 安装到底盖 (6) 上。
- 将 O 形密封圈安装到弯头 (5) 上后,利用螺栓将弯头 (5) 安装到机油冷却器上。
Show/hide table
图 5 g01004559 - 按拆解程序中标记的位置将密封垫和底盖 (4) 安装到机油冷却器芯 (3) 上。 将螺栓装入底盖 (4) 中。
Show/hide table
图 6 g01004313 - 将 O 形密封圈安装到管 (2) 的两头上。 利用干净的机油润滑 O 形密封圈。 将管 (2) 装入弯头 (1) 中。
- 将 O 形密封圈安装到弯头 (1) 上,并利用干净的机油润滑 O 形密封圈。 利用螺栓将弯头 (1) 和管 (2) 安装到机油冷却器芯上。
Show/hide table
图 1 | g01004839 |
注: 清洁中,确保不要损坏机油冷却器芯 (3) 内的管。
结束:
- 安装机油冷却器。 请参阅拆解和组装, "机油冷却器 - 安装"。
Caterpillar Information System:
3500B Engines Engine Oil Cooler - Disassemble
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0545 - FMI 05 Ether Start Relay open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0545 - FMI 06 Ether Start Relay short to ground
G3500 Engines Engine Oil Cooler - Install
3406E and 3456 Generator Set Engines Front Cover - Remove
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0248 - FMI 09 Cat Data Link not communicating
3304B and 3306B Engines for Caterpillar Built Machines Cylinder Head - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0274 - FMI 13 Atmospheric Pressure calibration required
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0274 - FMI 04 Atmospheric Pressure short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0263 - FMI 04 Digital Sensor Supply short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0263 - FMI 03 Digital Sensor Supply short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0262 - FMI 03 5 Volt Sensor DC Power Supply short to +batt
G3500 Engines Engine Oil Pump - Remove
3406E and 3456 Generator Set Engines Front Cover - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0827 - FMI 08 Left Exhaust Temperature signal abnormal
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0261 - FMI 13 Engine Timing calibration required
G3500 Engines Engine Oil Pump - Install
3408E and 3412E Engines for Caterpillar Built Machines Compression - Test
G3500 Engines Engine Oil Pump - Disassemble
3176C and 3196 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
3408E and 3412E Engines for Caterpillar Built Machines Cooling System - Inspect
G3500 Engines Engine Oil Pump - Assemble
3176C and 3196 Engines for Caterpillar Built Machines Cooling System - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Pump - Install