Generator - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 此步骤在 G3612 发动机上进行。 这是配备发电机的所有机型的典型步骤。
- 卸下联轴器护罩 (2) 、发电机护罩 (3) 及飞轮护罩 (1) 。
Show/hide table
图 1 | g01031948 |
- 卸下连接发动机联轴器法兰 (6) 和发电机联轴器法兰 (5) 的螺栓。 卸下联轴器盘 (7) 。
Show/hide table
图 2 | g00589972 |
Show/hide table
图 3 | g00589973 |
Show/hide table
图 4 | g00589974 |
- 卸下滤清器 (11) ,以便露出发电机底座右侧的安装螺栓及销的检修孔。
Show/hide table
图 5 | g01031950 |
- 使用 1/2 英寸螺栓及垫圈卸下销 (13) 。
注: 销孔的加工及销钉的安装完成前需进行最终对齐。
注: 标记发电机在底座上的位置。 将垫片保持在恰当位置,以便安装。
- 拧松对齐螺栓 (8) 。
- 拆下螺栓 (9) 。 检查螺栓上的密封件是否损坏。 如有必要,更换密封件。
- 将工具 (A) 和适当的起吊设备安装在发电机上。
- 从发电机底座上卸下发电机 (10) 。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
- 将工具 (A) 和适当的起吊设备连接至发电机。
Show/hide table
图 6 | g01031950 |
- 将发电机 (10) 定位在发电机底座上。
- 检查螺栓上的密封件是否损坏。 如有必要,更换密封件。 确保密封件安装在清洁的螺栓上。 安装螺栓 (9) 。
- 拧紧螺栓 (8) 。
- 安装销 (13) 。
- 安装四个滤清器 (11) 。
- 安装联轴器盘 (7) 。 安装将发动机联轴器法兰 (6) 连接至发电机联轴器法兰 (5) 的螺栓。
Show/hide table
图 7 | g00589974 |
Show/hide table
图 8 | g00589973 |
Show/hide table
图 9 | g00589972 |
- 安装飞轮护罩 (1) 、发电机护罩 (3) 及联轴器护罩 (2) 。
Show/hide table
图 10 | g01031948 |
Caterpillar Information System:
G3606 and G3608 Engines Air Valve - Remove and Install
G3500 Engines Vibration Damper - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fan Drive - Disassemble
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
3116 Truck Engine Walk-Around Inspection
3608 Engine Air Lubricator - Remove and Install
3116 Truck Engine Fuel Tank Water and Sediment - Drain
G3500 Engines Flywheel - Remove and Install
3406E and 3456 Generator Set Engines Engine Oil Pan
3116 Truck Engine Fuel Inlet Screen - Clean/Inspect/Replace
G3606 and G3608 Engines Air Silencer - Remove and Install
3116 Truck Engine Fuel Injection Timing - Check
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Sequence Valves - Remove and Install
120H and 135H Motor Graders Hydraulic and Steering System Gerotor Motor (Circle Drive)
3406E and 3456 Generator Set Engines Flywheel Housing
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
G3500 Engines Engine Oil Pan - Remove
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fan Drive - Assemble
G3500 Engines Engine Oil Pan - Install
G3606 and G3608 Engines Air Inlet Elbow - Remove and Install
G3500B Engines Fuel Metering Valve Screen - Check
G3500 Engines Engine Oil Pan - Disassemble
3406E and 3456 Generator Set Engines Electrical Ground Stud
G3606 and G3608 Engines Aftercooler - Remove