Fan Drive - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0510 | 冲头总成 | 1 |
- 使用适当的压具将轴 (9) 安装到支架组件 (17) 上。
注: 安装轴 (9) 前,确保轴 (9) 和支架 (17) 的润滑端口对准。
注: 安装前润滑轴 (9)。
注: 为防止损坏支架组件 (17),安装轴 (9) 时将支架组件 (17) 支撑在表面 (X) 上。
注: 安装后,从轴 (9) 的底座到轴 (9) 的顶部的测量应为
118.5 ± 0.75 mm (4.67± 0.03 inch) 。 - 安装螺栓 (16) 和垫圈,将轴 (9) 固定到支架组件 (17) 上。
- 如图所示,将衬套 (15) 安装到轴 (9) 上。
Show/hide table
图 4 g01211987 - 如图所示放置风扇皮带轮毂 (3)。 将轴承外圈 (14) 安装到风扇皮带轮毂 (3) 上。 用锤子和黄铜冲子确保轴承外圈 (14) 已固定。.
Show/hide table
图 5 g01212121 Show/hide table图 6 g01212125 - 如图所示放置风扇皮带轮毂 (3)。 将轴承外圈 (13) 安装到风扇皮带轮毂 (3) 上。 用锤子和黄铜冲子确保轴承外圈 (13) 已固定。
- 将轴承内圈(未显示)放入轴承外圈 (13) 中。
- 用密封的润滑剂润滑唇形密封 (12)(未显示)。 用工具 (A) 将唇形密封 (12)(未显示)安装到风扇皮带轮毂 (3) 上。
Show/hide table
图 7 g03651101 - 如图所示,将风扇皮带轮毂 (3) 放置到轴 (9) 上。 将隔套 (11) 安装到轴 (9) 上。
注: 轴 (9) 上的螺栓孔必须安装在图 7 中所示的 3 点和 9 点位置。
Show/hide table图 8 g03654210 - 将轴承内圈 (10) 安装到风扇皮带轮毂 (3) 上。
Show/hide table
图 9 g03653862 - 定位挡板 (8),如图所示。 安装螺栓 (7)。
Show/hide table
图 10 g03654248 - 将适当的起吊设备连接到风扇驱动皮带轮 (5) 上。
- 将风扇驱动皮带轮 (5) 放置到风扇皮带轮毂 (3) 上。 安装螺栓 (6),将风扇驱动皮带轮 (5) 固定到风扇皮带轮毂 (3) 上。 风扇驱动皮带轮 (5) 的重量约为
65 kg (144 lb) 。Show/hide table图 11 g01052047 - 将 O 形密封圈 (4) 安装到适配器 (1) 上。
Show/hide table
图 12 g01211375 - 将适配器 (1) 放置到风扇皮带轮毂 (3) 上。 安装螺栓 (2) 以将适配器 (1) 固定到风扇皮带轮毂 (3) 上。
Show/hide table
图 1 | g01211490 |
Show/hide table
图 2 | g03623137 |
Show/hide table
图 3 | g01211485 |
结束:
- 安装风扇驱动装置。 请参阅拆解和组装, "风扇驱动装置 - 安装"。
Caterpillar Information System:
G3500 Engines Engine Oil Pan - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
3406E and 3456 Generator Set Engines Flywheel Housing
120H and 135H Motor Graders Hydraulic and Steering System Gerotor Motor (Circle Drive)
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Sequence Valves - Remove and Install
G3606 and G3608 Engines Generator - Remove and Install
G3606 and G3608 Engines Air Valve - Remove and Install
G3500 Engines Vibration Damper - Remove and Install
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Fan Drive - Disassemble
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
3116 Truck Engine Walk-Around Inspection
3608 Engine Air Lubricator - Remove and Install
G3500 Engines Engine Oil Pan - Install
G3606 and G3608 Engines Air Inlet Elbow - Remove and Install
G3500B Engines Fuel Metering Valve Screen - Check
G3500 Engines Engine Oil Pan - Disassemble
3406E and 3456 Generator Set Engines Electrical Ground Stud
G3606 and G3608 Engines Aftercooler - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
G3606 and G3608 Engines Aftercooler - Install
G3500 Engines Engine Oil Pan - Assemble
G3500 Engines Engine Air Cleaner Service Indicator - Inspect
3406E and 3456 Generator Set Engines Exhaust Manifold
G3500 Engines Engine Oil and Water Pump Drive - Assemble